D-Link DSR-250N Support and Manuals
Get Help and Manuals for this D-Link item
This item is in your list!
View All Support Options Below
Free D-Link DSR-250N manuals!
Problems with D-Link DSR-250N?
Ask a Question
Free D-Link DSR-250N manuals!
Problems with D-Link DSR-250N?
Ask a Question
Popular D-Link DSR-250N Manual Pages
Product Manual - Page 5
... Users and Passwords 109
7.2 Using SSL VPN Policies 110 7.2.1 Using Network Resources 113
7.3 Application Port Forwarding 114
7.4 SSL VPN Client Configuration 116
7.5 User Portal ...118 7.5.1 Creating Portal Layouts 119
Chapter 8. Unified Services Router
User Manual
4.3.1 4.4 4.5 4.6
Primary benefits of Virtual APs 61 Tuning Radio Specific Settings 62 Advanced Wireless Settings 63 Wi...
Product Manual - Page 15
... acknowledging a DHCP request from another PC on your PCs, set the DHCP mode to display the router's
management login screen.
Default login credentials for the management GUI:
Username: admin
Password: admin
If the router's LAN IP address was changed, use a Windows Internet Naming Service (WINS) server. DHCP relay can also enable DNS proxy...
Product Manual - Page 31
... your ISP may require you have multiple PPPoE support).
ISP login information. Unified Services Router
User Manual
3G Internet access with the primary WAN port (WAN1) configuration only.
3.2 WAN Configuration
Setup > Internet Settings > WAN1 Setup
You must either allow the router to -Point Encryption (MPPE).
Split Tunnel (supported for the selected ISP type become...
Product Manual - Page 33
There are defined on the WAN Configuration page. Unified Services Router
Figure 12: Manual WAN configuration
User Manual
3.2.4 PPPoE
Setup > Internet Settings
The PPPoE ISP settings are two types of PPPoE ISP's supported by the DSR: the standard username/password PPPoE and Japan Multiple PPPoE.
31
Product Manual - Page 34
... GUI will prompt you for authentication, service, and connection settings in Japan, the use a single control and data connection, and require username / password credentials to login and authenticate the DSR with the ISP. control) traffic between the DSR and the ISP. Unified Services Router
Figure 13: PPPoE configuration for standard ISPs
User Manual
Most PPPoE ISP's use of...
Product Manual - Page 64
... legacy connections or only 802.11n connections (or both) are appropriate for most networks. Unified Services Router
User Manual
broadcast the SSID for the VAP with WEP since it is similarly governed by regulatory constraints based on this scenario.
4.4 Tuning Radio Specific Settings
Setup > Wireless Settings > Radio Settings
The Radio Settings page lets you configure the channels...
Product Manual - Page 92
... used for either be required on the internet (remote access).
Set the Connection Name and pre-shared key: the connection name is created, you can modify it as required. Unified Services Router
User Manual
6.1 VPN Wizard
Setup > Wizard > VPN Wizard
You can use the VPN wizard to establish the tunnel
Determine the local gateway for this...
Product Manual - Page 100
PPTP Server
User Manual
6.4.2 L2TP Tunnel Support
Setup > VPN Settings > L2TP > L2TP Server
A L2TP VPN can reach the router's L2TP server. Once enabled a L2TP server is enabled, L2TP clients that are within the range of configured IP addresses of allowed clients can be established through this router. Once the L2TP server is available on the router for LAN and WAN L2TP...
Product Manual - Page 171
Unified Services Router
User Manual
%s:DBUpdate event: Table: %s opCode:%d rowId:%d %s:%d SIP ENABLE: %s sipTblHandler:failed to update ifStatic sipTblHandler:failed to update Configport
DEBUG DEBUG DEBUG DEBUG
%s:%d SIP DISABLE: %s
DEBUG
%s:%d SIP SET CONF: %s
DEBUG
Failed to open %s: %s Failed to start sipalg
DEBUG DEBUG
Failed to stop sipalg
DEBUG
Failed to get config info
DEBUG
...
Product Manual - Page 184
...message radEapRecvTask: " failed to initialize UMI umiRegister failed. nRows=%d nCols=%d sqlite3QueryResGet failed empty result. Unable to set default retries value ERROR: incomplete DB update information. Unified Services Router
User Manual
Adding Dictionary Attribute '%s'
DEBUG
Adding Dictionary Value %s
DEBUG
Receiving attribute: %s Processing attribute: %s Processing attribute...
Product Manual - Page 185
... level for radAuth. nRows=%d nCols=%d Error in the list after semTake reply timeout
DEBUG DEBUG DEBUG
Unable to set debug level for radAuth. Unified Services Router
User Manual
Next Synchronization after" Next Synchronization after %d \ Primary is not available, " Secondary is not available, "
DEBUG DEBUG DEBUG DEBUG
Invalid value for use default servers, " No server is configured...
Product Manual - Page 192
... to get the channel setting for node : %s installing key to UMI iappSockInit() failed iappInit got error, unregistering it with key %s
Unknown IAPP command %d received.
unable to register to index %d iReq.i_val : %d pIfName : %s
iReq.i_val : %d
setting mode: %d
Global counter wrapped, re-generating... Unified Services Router
User Manual
Facility: Local0 (Wireless)
Log Message (node...
Product Manual - Page 194
... ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR
192
"
Message from authenticator: from pnacRadXlateDemoRecv: malloc failed From pnacRadXlateRadPktHandle: received a non-supported" Only md5 authentication scheme currently supported. Unified Services Router
User Manual...
Product Manual - Page 199
...: maxAuth limit reached
pnacAuthConfig: malloc failed Error from pnacAuthConfig: pAsArg cannot be 0-3. Unified Services Router
User Manual
Failed to initiate PBC based enrolle association Invalid association mode. (Allowed modes : PIN/PBC)
ERROR ERROR
wpsEnable: running wsccmd failed Failed to send QUIT command to WSC from DOT11
Failed to allocate buffer PNAC user comp id not set.
Product Manual - Page 200
...%d
ERROR
ERROR
ERROR ERROR ERROR
198 ERROR
Profile %s does not exist
ERROR
Invalid Cipher type %d
ERROR
Cipher %s not found in the list. supported values are 1,2,3,4
ERROR ERROR
Profile %s does not exist ERROR: incomplete DB update information.
Unified Services Router
User Manual
Invalid Cipher type %d Profile supports WEP stas,Group cipher must be WEP
ERROR ERROR
Profile...
D-Link DSR-250N Reviews
Do you have an experience with the D-Link DSR-250N that you would like to share?
Earn 750 points for your review!
We have not received any reviews for D-Link yet.
Earn 750 points for your review!