Cisco WS-C2960S-24TS-L Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-C2960S-24TS-L manuals!
Problems with Cisco WS-C2960S-24TS-L?
Ask a Question
Free Cisco WS-C2960S-24TS-L manuals!
Problems with Cisco WS-C2960S-24TS-L?
Ask a Question
Cisco WS-C2960S-24TS-L Videos
63% off for WS C2960S 24TS L switch at Router Switch com
Duration: :51
Total Views: 10
Duration: :51
Total Views: 10
Buy Cisco WS-C2960S-24TS-S switch $625.00: 3Anetwork.com
Duration: :30
Total Views: 41
Duration: :30
Total Views: 41
Buy Cisco WS-C2960S-24TS-L Switch $890.00 : 3Anetwork.com
Duration: :45
Total Views: 29
Duration: :45
Total Views: 29
Popular Cisco WS-C2960S-24TS-L Manual Pages
Hardware Installation Guide - Page 2
... of California.
All other company. (1002R)
Any Internet Protocol (IP) addresses used in part 15 of their own expense. The following information is not installed in this document are service marks; THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION...
Hardware Installation Guide - Page 7
If you are interested in more information, see the Cisco IOS documentation set from the Cisco.com home page by choosing Support > Documentation > Product and Support Documentation/Cisco IOS Software.
Caution Means reader be careful. Preface
Audience
This guide is for the networking or computer technician responsible for notes, cautions, and warnings:
Note Means reader take note.
Notes ...
Hardware Installation Guide - Page 9
... Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application.
Preface
• Cisco Redundant Power System 2300 Hardware Installation Guide • Cisco RPS 675 Redundant Power System Hardware Installation Guide These compatibility matrix documents are a free service and Cisco currently supports RSS Version 2.0. OL-7075-09
Catalyst...
Hardware Installation Guide - Page 22
..., and the CLI provide PoE settings for Cisco IP Phones and Cisco Aironet Access Points.
• Each of the PoE ports on Power over Ethernet (PoE) circuits if interconnections are made using such interconnection methods, unless the exposed metal parts are located within a restricted access location and users and service people who are authorized within the...
Hardware Installation Guide - Page 30
... RPS support
1-20
Catalyst 2960 Switch Hardware Installation Guide
OL-7075-09
It automatically senses when the internal power supply of a connected switch fails and provides power to one or two failed switches at a time. The internal power supply is a redundant power system that supports input voltages between 100 and 240 VAC. Warning Attach only the following Cisco RPS model to...
Hardware Installation Guide - Page 36
... on page B-5, which can use of the hazard. Statement 1072
Warning No user-serviceable parts inside the chassis, which lists the cable specifications for
1000BASE-X and 100BASE-X SFP modules for Particulate Matter
Cisco Ethernet switches are equipped with local and national electrical codes. Installation Guidelines
This section does not apply to those switches, see Chapter 3, "Switch...
Hardware Installation Guide - Page 46
... of the unit. Place the switch on the wall, do not support autonegotiation, you can explicitly set can reduce performance or result in the mounting-kit envelope. See the Catalyst 2960 Switch Getting Started Guide for instructions.
• Connect to complete the installation:
• Power on page 2-5.
• Connect to Appendix C, "Configuring the Switch with the...
Hardware Installation Guide - Page 48
... might be replaced by arrows that you feel the connector on installing, removing, and cabling the SFP module, refer to your wrist and to a bare metal surface on the Catalyst 2960 switch.
See Figure 2-15.
2-16
Catalyst 2960 Switch Hardware Installation Guide
OL-7075-09 Cisco SFP modules and the Catalyst 2960 switch support the Quality...
Hardware Installation Guide - Page 57
...and national electrical codes. OL-7075-09
Catalyst 2960 Switch Hardware Installation Guide
3-3 Statement 1073
Warning Installation of a suitably installed ground conductor.
...Installation Guidelines
This section is installed, the following ports must be connected through the vents must be sure to all national laws and regulations. Statement 1046
Warning No user-serviceable parts...
Hardware Installation Guide - Page 73
... interface, from the command-line interface (CLI), or from an SNMP workstation. See the software configuration guide, the switch command reference guide on Cisco.com, or the documentation that came with your SNMP application for troubleshooting problems: • Diagnosing Problems, page 4-1 • Clearing the Switch IP Address and Configuration, page 4-5 • Locating the Switch Serial...
Hardware Installation Guide - Page 76
...on fiber-optic connections. Catalyst 2960 Switch Hardware Installation Guide
4-4
OL-7075-09
A unidirectional link can happen when you troubleshoot switch performance problems: • Speed, Duplex, and Autonegotiation, ... or interface error-disabled, disabled, or shutdown status on fiber-optic links. A common issue with speed and duplex occurs when the duplex settings are mismatched ...
Hardware Installation Guide - Page 77
.... OL-7075-09
Catalyst 2960 Switch Hardware Installation Guide
4-5
Do not follow one of these steps to return your NIC card might be set to autonegotiate, yet sometimes autonegotiation issues occur. To troubleshoot autonegotiation problems, try to manually set both ends of the connection. See Appendix B, "Cable and Adapter Specifications."
Caution This procedure clears the IP...
Hardware Installation Guide - Page 83
...2960-48TC-L, 2960-48TT-S, and 2960-48TT-L Switch Specifications
Power Requirements AC input voltage
DC input voltage for RPS 2300 DC input voltage for RPS 675 Power consumption Power rating Physical Dimensions Weight Dimensions (H x D x W)
100 to 240...24T-L) 12 lb (5.44 kg) (Catalyst 2960G-48TC-L 1.73 x 12.9 x 17.5 in. (4.39 x 32.76 x 44.45 cm)
Catalyst 2960 Switch Hardware Installation Guide
A-3
Hardware Installation Guide - Page 98
... to a Cisco redundant power system (RPS), refer to configure and manage the switch.
Entering the Initial Configuration Information
To set up the switch, you are usually fatal. This information is powered up.
If a switch fails POST, the System LED turns amber.
You need to the power connector on a switch rear panel. Catalyst 2960 Switch Hardware Installation Guide
C-4
OL...
Hardware Installation Guide - Page 107
...ports 3-3 ground connection 2-4, 3-3 grounded equipment 2-3, 3-3 installation 2-2, 3-1 installation instructions 2-2, 3-2 jewelry removal 2-2, 3-2 lightning activity 2-2, 3-2 local and national electrical codes compliance 2-4, 3-3 more than one power supply 3-3 no user-serviceable parts 2-4 overheating prevention 2-2, 3-1 plug-socket combination 2-3 PoE 3-2 power supplies 2-3 prevent bodily injury...
Cisco WS-C2960S-24TS-L Reviews
We have not received any reviews for Cisco yet.