Cisco WS-C3560V2-24TS-E Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-C3560V2-24TS-E manuals!
Problems with Cisco WS-C3560V2-24TS-E?
Ask a Question
Free Cisco WS-C3560V2-24TS-E manuals!
Problems with Cisco WS-C3560V2-24TS-E?
Ask a Question
Popular Cisco WS-C3560V2-24TS-E Manual Pages
Command Reference - Page 19
... have experience working with the concepts and terminology of Ethernet and local area networking. Purpose
The Catalyst 3560 switch is for this guide, you should have experience working with the Catalyst 3560 switches. For more information, see the Cisco IOS documentation set of service (QoS), static routing, and the Routing Information Protocol (RIP). To distinguish it from the...
Command Reference - Page 102
... 2 Catalyst 3560 Switch Cisco IOS Commands
deny (ARP access-list configuration)
Use the deny Address Resolution Protocol (ARP) access-list configuration command to remove the specified access control entry (ACE) from the access list. Use the no default settings. Deny the sender MAC address. Defaults
There are no form of the ARP access list, there is running the IP services...
Command Reference - Page 103
... lists.
78-16405-05
Catalyst 3560 Switch Command Reference
2-71 Usage Guidelines You can verify your settings by entering the show arp access-list
Description Defines an ARP access control list ...-list ip arp inspection filter vlan
permit (ARP access-list configuration) show arp access-list privileged EXEC command.
Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
deny (ARP access-list ...
Command Reference - Page 104
...switch is running the advanced IP services image and you have configured a dual IPv4 and IPv6 Switch Database Management (SDM) template on the switch.
2-72
Catalyst 3560 Switch...-code]...set deny conditions for an IPv6 access list. deny (IPv6 access-list configuration)
Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
deny (IPv6 access-list configuration)
Use the deny command in IPv6 access list...
Command Reference - Page 108
... all other traffic to the console. Filters incoming or outgoing IPv6 traffic on a Layer 3 interface. deny (IPv6 access-list configuration)
Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
This is at the end of each IPv6 access list. The second deny also logs all packets that have a source UDP port number less than 5000 from leaving the...
Command Reference - Page 110
... 12.1(19)EA1
Modification This command was introduced.
2-78
Catalyst 3560 Switch Command Reference
78-16405-05 mask is a mask of IPX encapsulation being used.
However;
the default action for a MAC-named ACL is not supported as specified in Novell terminology and Cisco IOS terminology are listed in decimal, hexadecimal, or octal. Filter criteria for a match...
Command Reference - Page 111
... guide for non-IP traffic.
if you do not use the host keyword, you must enter an address mask.
Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
deny (MAC access-list configuration)
Usage Guidelines
You enter MAC-access list configuration mode by entering the show access-lists
Description Creates an access list based on a switch.
78-16405-05
Catalyst 3560 Switch...
Command Reference - Page 230
... list named cisco:
Switch (config)# interface gigabitethernet0/1 Switch(config-if)# no switchport Switch(config-if)# ipv6 address 2001::/64 eui-64 Switch(config-if)# ipv6 traffic-filter cisco in
Related Commands
Command ipv6 access-list
show ipv6 access-list show ipv6 interface
Description Defines an IPv6 access list and sets deny or permit conditions for IPv6.
2-198
Catalyst 3560 Switch...
Command Reference - Page 387
....
If the BOOT environment variable is set , the system attempts to read and write a nonvolatile copy of the boot loader.
Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
show boot
Table 2-17
show boot Field Descriptions
Field BOOT path-list
Config file Private Config file Enable Break Manual Boot Helper path-list NVRAM/Config file buffer size
Description
Displays...
Command Reference - Page 408
...power inline
Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
Examples
This is an example of output from the show controllers power inline command on a switch other than a Catalyst 3560G-48PS or 3560G-24PS switch:
Switch> show controllers power...C5 57 03 12 20 04 B2 05 06 07 07
Error State
:00 00 00 00 10 00
Error Code
:00 00 00 00 00 00 00 00 00 00 00 00
Power Status
:N Y N N Y N N N N N...
Command Reference - Page 728
... be enabled.
2-696
Catalyst 3560 Switch Command Reference
78-16405-05 If you make all VTP switches in transparent mode, the changes are case sensitive.
Follow these guidelines when setting VTP pruning:
• VTP pruning removes information about each pruning-eligible VLAN from the switch.
• The VTP mode must support Version 2; Passwords should match on the...
Command Reference - Page 731
...switch in server mode, that it does not return an error if the switch is not in client or transparent mode.
• If the receiving switch is in the running -config startup-config privileged EXEC command. If you attempt to set...these guidelines when setting the VTP mode:
• The no vtp client and no vtp transparent forms of the server. Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
vtp ...
Command Reference - Page 737
Appendix A Catalyst 3560 Switch Boot Loader Commands boot
Related Commands Command set
Description
Sets the BOOT environment variable to boot a specific image when the BOOT keyword is appended to the command.
78-16405-05
Catalyst 3560 Switch Command Reference
A-3
Command Reference - Page 761
Caution
Because debugging output is best to troubleshoot specific problems or during periods of Cisco technical support staff. For this reason, use the debug commands only to use the debug commands during troubleshooting sessions with the Catalyst 3560 switch. It is assigned high priority in diagnosing and resolving internetworking problems and should be enabled only under the guidance ...
Command Reference - Page 834
...support debug messages. Debug Multiple Spanning Tree Protocol events. This shim is the software module that is the same as the no debug spanning-tree command.
B-74
Catalyst 3560 Switch Command Reference
78-16405-05 debug spanning-tree
Appendix B Catalyst 3560 Switch... Tree Protocol (STP) code and the platform-specific code of various switch platforms. Display UplinkFast-event...
Cisco WS-C3560V2-24TS-E Reviews
We have not received any reviews for Cisco yet.