Cisco ATA188-I2 Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco ATA188-I2 manuals!
Problems with Cisco ATA188-I2?
Ask a Question
Free Cisco ATA188-I2 manuals!
Problems with Cisco ATA188-I2?
Ask a Question
Popular Cisco ATA188-I2 Manual Pages
User Guide - Page 1
At A Glance
Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor
1 Overview 2 Installation 3 Configuration
User Guide - Page 2
... signaling image protocol (SCCP, MGCP, H.323 or SIP), available on the World Wide Web at the following location: http://www.cisco.com/univercd/cc/td/doc/product/voice/ata/ind ex.htm Figure 1 Cisco ATA Analog Telephone Adaptor
ANALOCGISTCELOEPAHTONAE1A8D6APTOR
2
72209 1 Overview
This guide contains basic instructions for your Cisco Analog Telephone Adaptor (Cisco ATA 186 or Cisco ATA 188).
User Guide - Page 4
Cisco ATA 188
The Cisco ATA 188 connects one or two analog telephones to an IP-based telephony network. The hardware features include:
...100BASE-T data port • Two link activity (LINK) LEDs • Power connector Figure 3 shows the rear panel of the Cisco ATA 188. Figure 3 Cisco ATA 188 Rear Panel
72211
PHONE 1 PHONE 2
LINK 10/100 PC 10/100 UPLINK LINK 5V
RJ-11 FXS ports LINK LED
Power...
User Guide - Page 11
...
Installation Requirements
The analog telephone adaptor (ATA) package includes: • Cisco ATA 186 or Cisco ATA 188 Analog Telephone Adaptor • Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor At A Glance (this document) • Regulatory Compliance and Safety Information for the Cisco ATA 186 and Cisco ATA 188. • 5V power adaptor • Power cord
Caution
The Cisco ATA...
User Guide - Page 12
... connections. • Access to another Ethernet device (such as a router or PC) without quality degradation, and a Category-3 Ethernet cable supports 100BASE-T for each
12 Otherwise, use a crossover Ethernet cable to connect the Cisco ATA to an IP network • One or two analog Touch-Tone telephones or fax machines, or one of each Ethernet...
User Guide - Page 13
Refer to the Cisco ATA administrator guide for the Cisco ATA 186. Installation Steps
Figure 4 illustrates the cabling for your particular signaling image protocol (SCCP, MGCP, H.323 or SIP), available on the World Wide Web at the following location: http://www.cisco.com/univercd/cc/td/doc/product/voic e/ata/index.htm
13 Figure 5 illustrates the cabling for the Cisco ATA 188. Note Before ...
User Guide - Page 15
Figure 5 Cabling the Cisco ATA 188
72213
PHONE 1 PHONE 2
LINK 10/100 PC 10/100 UPLINK LINK 5V
Analog telephones (or fax)
IP network
PC
5V power
adaptor
Power outlet Power cord
15
User Guide - Page 17
... properly. Note If you must be switched to tone setting (not pulse) for the Cisco ATA 188, this is the 10/100UPLINK connector.
17 for the Cisco ATA to the uplink RJ-45 connector on the Cisco ATA.
Step 3 (Optional) Connect the telephone line cord of a second telephone to the Cisco ATA, you are connecting only one telephone to the...
User Guide - Page 18
Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240VAC, 10A international) is used on the building's installation for short-circuit (overcurrent) protection.
Step 5 Step 6 Step 7
(Cisco ATA 188 only-optional) Connect a straight-through Ethernet cable from your PC to the 5V DC power adaptor.
Warning
This product relies on the phase...
User Guide - Page 19
This LED is labeled ACT on the rear panel of the Cisco ATA 188. Caution
Do not cover or block the air vents on the rear panel of the Cisco ATA 186 and is properly connected and powered up, the green activity LED flashes to indicate network activity. Overheating can cause permanent damage to the unit...
User Guide - Page 20
... following connectors and indicators:
• 5V power connector.
• Two RJ-11 FXS (Foreign Exchange Station) ports-The Cisco ATA supports two independent RJ-11 telephone ports that can be used simultaneously.
20 Each port supports either voice calls or fax sessions, and both ports can connect to any standard analog telephone device.
Procedure...
User Guide - Page 21
..., check your specific application. The Cisco ATA 188 has two Ethernet ports: an RJ-45 10/100BASE-T uplink port to connect the Cisco ATA 188 to a 10...Cisco ATA 186 has one RJ-45 10BASE-T uplink Ethernet port to connect the Cisco ATA 186 to the network.
21 The Cisco ATA186-I2 and Cisco ATA188-I2 provide 270 ohm + 750 ohm // 150-nF complex impedance. Note The Cisco ATA186-I1 and Cisco ATA188-I1...
User Guide - Page 22
... activity and is solid when there is a link.
• The Cisco ATA 186 RJ-45 LED is solid when the Cisco ATA is powered on and blinks to show network activity.
• Function button... full-duplex operation. The Cisco ATA 186 is capable of the unit (see Figure 6).
22 The LED blinks twice when the Cisco ATA is no link or activity. Note The Cisco ATA 188 performs auto-negotiation for duplexity...
User Guide - Page 24
... Cisco ATA administrator's guides are using (SCCP, MGCP, H.323 or SIP).
For additional information about the voice configuration menu in your administrator's guide. Doing so may interfere with the process and may permanently disable the Cisco ATA.
3 Configuration
For complete configuration information, see the information about the voice configuration menu, see the administrator's guide...
User Guide - Page 26
...Cisco ATA. if this phone does not work either, there may be a problem with the current configuration or with the Cisco ATA....
• A busy tone indicates that the party you dialed an invalid number.
• After power up, if the function button continues to blink slowly, the Cisco ATA... your Cisco ATA is ... through service providers,...
Cisco ATA188-I2 Reviews
We have not received any reviews for Cisco yet.