Cisco AIR-BR1310G-A-K9 - Aironet 1310 Outdoor Access Point/Bridge Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco AIR-BR1310G-A-K9 manuals!
Problems with Cisco AIR-BR1310G-A-K9?
Ask a Question
Free Cisco AIR-BR1310G-A-K9 manuals!
Problems with Cisco AIR-BR1310G-A-K9?
Ask a Question
Most Recent Cisco AIR-BR1310G-A-K9 Questions
How To Reset A Cisco Air-br1310g-a-k9-r
(Posted by lizdal 9 years ago)
How To Reset Cisco Air-br1310g
(Posted by sambathonline 12 years ago)
How Do I Access And Reset The Password On My Cisco Air-br1310g-a-k9
(Posted by keving38 12 years ago)
Popular Cisco AIR-BR1310G-A-K9 Manual Pages
Hardware Installation Guide - Page 5
... Connecting to the Console Serial Port 5-6 Configuring Controller Information 5-7 Clearing Manually Entered Controller Information 5-7 Manually Resetting the Access Point to Defaults 5-8 Returning the Access Point to Autonomous Mode 5-8 Using a Controller to Return the Access Point to Autonomous Mode 5-8
Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide
v
Hardware Installation Guide - Page 10
...," indicates how to the power injector's console serial port. Appendix E, "Console Serial Cable Pinouts," identifies the pinouts for Lightweight Access Points," describes the procedure to convey instructions and information: • Commands and keywords are in this publication.
Appendix C, "Access Point Specifications," describes the channels and antenna settings supported by the world...
Hardware Installation Guide - Page 24
...
117059
1 Integrated antenna access point/bridge configuration
2 External antenna access point/bridge configuration with the access point/bridge)
Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide
1-4
OL-5048-06
Power
The access point/bridge receives inline power from the power injector to the access point/bridge. The power injector is available...
Hardware Installation Guide - Page 25
... polarization 13.5-dBi yagi antenna 14-dBi sector antenna with a radome to support single or diversity antenna configurations. Two reverse-TNC type RF connectors are provided on the end of the unit to protect it from environmental elements. OL-5048-06
Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide
1-5 The antenna is covered with vertical...
Hardware Installation Guide - Page 26
...Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide
1-6
OL-5048-06 Enclosure
The access point/bridge uses an enclosure that supports indoor or outdoor operating environments. (refer to provide Ethernet signals and in -line power • External antenna access point/bridge configuration
-
Dual antenna connectors-used to "Access Point Specifications...
Hardware Installation Guide - Page 40
... antenna configuration • Power injector (LR2) unit • Power module and AC power cord • Quick start guide • Mounting instructions document • Read Me document • Translated safety warnings document • Cisco product registration and Cisco documentation feedback cards
Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide...
Hardware Installation Guide - Page 41
... to become familiar with 4 mounting bolts and washers • Two sub-mini RG-59 coax cables (12 in. Following installation, access to the unit should be password-protected by the network administrator to maintain regulatory compliance. OL-5048-06
Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide
2-7
The optional roof mount kit contains these items...
Hardware Installation Guide - Page 44
... Mount the access point/bridge to the Cisco IOS Software Configuration Guide for short-circuit (overcurrent) protection. Warning
This equipment must be grounded. Warning This product relies on the building's installation for Access Points or the Cisco Wireless LAN Controller Configuration Guide.
2-10
Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide...
Hardware Installation Guide - Page 47
...OL-5048-06
Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide
3-3 Note You should take this extra loss into account when planning antenna gains and power settings. Connect the ground wire to the mast bracket using a small wrench.
6. Mount the mast bracket to the mounting lugs on the mast bracket using the support pins. 4. Tighten the...
Hardware Installation Guide - Page 50
... the antenna.
• Preconfigured access point or workgroup bridge modes-the bridge Install LED does not operate. Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide
3-6
OL-5048-06 Amber
Non-root, associated Associated (non-root mode). Green blinking Root, searching
Not associated (root mode). Disconnect power to a root bridge, the Install LED turns...
Hardware Installation Guide - Page 53
...the Console Serial Port, page 4-14 • Obtaining the TFTP Server Software, page 4-15
OL-5048-06
Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide
4-1 CH A P T E R
4
Troubleshooting Autonomous Access Points and Bridges
This chapter provides troubleshooting procedures for basic problems with the autonomous access point/bridge (model: AIR-BR1310G).
Hardware Installation Guide - Page 55
.... If the problem continues, contact technical support for assistance.
Not associated (root mode).
OL-5048-06
Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide
4-3 LED Indications (continued)
Status LED
Blinking green
Radio LED
- Blinking -
- Off
-
-
- Blinking - green
-
-
Radio firmware error-disconnect and reconnect...
Hardware Installation Guide - Page 73
... • Cisco Aironet Power Injector LR2T-optional transportation version - 12-
to 40-VDC input power
Checking Power
You can use DHCP Option 43 to provide a list of power to the power injector. Uses the 48-VDC power module (included with the access point)
- 48-VDC input power - OL-5048-06
Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide
5-5
Hardware Installation Guide - Page 75
... 5
Set up a terminal emulator to associate with the access point. To clear or remove the manually entered controller information, you can use these EXEC mode CLI commands: clear lwapp ap ip address clear lwapp ip default-gateway clear lwapp controller ip address clear lwapp ap hostname
OL-5048-06
Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide...
Hardware Installation Guide - Page 98
Appendix D Channels and Maximum Power Levels
Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide
D-2
OL-5048-06
Cisco AIR-BR1310G-A-K9 Reviews
We have not received any reviews for Cisco yet.