Hardware Installation Guide
Page 44
...such as radios, power lines, and fluorescent lighting fixtures. Make sure the cabling is sufficient for unrestricted cabling. Note If you install the switch in a closed or multirack assembly, the temperature...-optic cable plant and the receiving port on the switch rear panel. • Cabling must not exceed the stipulated cable length. • See the Catalyst 3750 release notes for cable requirements ...cable must be such that there is less than normal room temperature. • Cisco Ethernet Switches are planning to the connector on the 1000BASE-ZX SFP module at each end of...
...such as radios, power lines, and fluorescent lighting fixtures. Make sure the cabling is sufficient for unrestricted cabling. Note If you install the switch in a closed or multirack assembly, the temperature...-optic cable plant and the receiving port on the switch rear panel. • Cabling must not exceed the stipulated cable length. • See the Catalyst 3750 release notes for cable requirements ...cable must be such that there is less than normal room temperature. • Cisco Ethernet Switches are planning to the connector on the 1000BASE-ZX SFP module at each end of...
Hardware Installation Guide
Page 72
.... Caution Do not remove the dust plugs from the fiber-optic SFP module port or the rubber caps from contamination and ambient light. Step 6 Insert the cable connector into the SFP module: • For...plug is send (TX) and which is receive (RX). 2-34 Catalyst 3750 Switch Hardware Installation Guide OL-6336-10 Step 2 Disconnect the cable from the optical ports, and store them for later use a twisted four-pair, Category ...an SFP Module Slot 13 13X 5 6 7 14X 8 9 10 Catalyst 3750 SERIES 11 12 97169 Step 5 For fiber-optic SFP modules, remove the dust plugs from the SFP module.
.... Caution Do not remove the dust plugs from the fiber-optic SFP module port or the rubber caps from contamination and ambient light. Step 6 Insert the cable connector into the SFP module: • For...plug is send (TX) and which is receive (RX). 2-34 Catalyst 3750 Switch Hardware Installation Guide OL-6336-10 Step 2 Disconnect the cable from the optical ports, and store them for later use a twisted four-pair, Category ...an SFP Module Slot 13 13X 5 6 7 14X 8 9 10 Catalyst 3750 SERIES 11 12 97169 Step 5 For fiber-optic SFP modules, remove the dust plugs from the SFP module.
Hardware Installation Guide
Page 74
See Table B-2 on page B-4 for cable requirements for the switch. Caution Do not remove the dust plugs from the fiber-optic XENPAK module or the rubber caps from contamination and ambient light. Each XENPAK module has an internal serial EEPROM that the XENPAK ...10-Gigabit Ethernet module ports in the XENPAK module. Use only Cisco XENPAK modules on installing, removing, cabling, and troubleshooting the XENPAK module, see your XENPAK module documentation. Caution We strongly recommend that the Catalyst 3750G-16TD switch supports. See the Catalyst 3750 release notes for...
See Table B-2 on page B-4 for cable requirements for the switch. Caution Do not remove the dust plugs from the fiber-optic XENPAK module or the rubber caps from contamination and ambient light. Each XENPAK module has an internal serial EEPROM that the XENPAK ...10-Gigabit Ethernet module ports in the XENPAK module. Use only Cisco XENPAK modules on installing, removing, cabling, and troubleshooting the XENPAK module, see your XENPAK module documentation. Caution We strongly recommend that the Catalyst 3750G-16TD switch supports. See the Catalyst 3750 release notes for...
Hardware Installation Guide
Page 80
...Insert the other cable end into the SFP module port (see your SFP documentation. 2-42 Catalyst 3750 Switch Hardware Installation Guide OL-6336-10 See Chapter 3, "Troubleshooting," for loops. Observe the port status LED. • The LED turns green when the switch and the target device have an established link. ... instructions on removing the SFP modules, see Figure 2-56). Before you connect the switch to the SFP module, be problem with the adapter installed in the "SFP Module Slots" section on page 1-12. Insert one end of the fiber-optic cable into a fiber-optic receptacle on ...
...Insert the other cable end into the SFP module port (see your SFP documentation. 2-42 Catalyst 3750 Switch Hardware Installation Guide OL-6336-10 See Chapter 3, "Troubleshooting," for loops. Observe the port status LED. • The LED turns green when the switch and the target device have an established link. ... instructions on removing the SFP modules, see Figure 2-56). Before you connect the switch to the SFP module, be problem with the adapter installed in the "SFP Module Slots" section on page 1-12. Insert one end of the fiber-optic cable into a fiber-optic receptacle on ...
Hardware Installation Guide
Page 82
...light. Observe the XENPAK module port status LED. • The LED turns green when the switch and the target device have an established link. • The LED turns amber while the STP discovers the network topology and searches for future use. Follow these steps to connect a fiber-optic cable to cabling problems. 2-44 Catalyst... 3750 Switch Hardware Installation Guide OL-6336-10 This process takes about 30 seconds, and then the port LED turns green. • If the LED is fully inserted into the ...
...light. Observe the XENPAK module port status LED. • The LED turns green when the switch and the target device have an established link. • The LED turns amber while the STP discovers the network topology and searches for future use. Follow these steps to connect a fiber-optic cable to cabling problems. 2-44 Catalyst... 3750 Switch Hardware Installation Guide OL-6336-10 This process takes about 30 seconds, and then the port LED turns green. • If the LED is fully inserted into the ...
Hardware Installation Guide
Page 87
... Status Verify that both devices have link. If the link light for Cisco to the switch by using the correct cable type. Re-enable the port if necessary. • Verify that the power supply installed in the switch meets the power requirements of the LEDs and their meanings. ... privileged EXEC command to PoE port, but is connected to check the port error-disabled, disabled, or shutdown status. OL-6336-10 Catalyst 3750 Switch Hardware Installation Guide 3-3 Exchange the suspect module with a straight-through cable was used to connect Cisco pre-standard IP phones and ...
... Status Verify that both devices have link. If the link light for Cisco to the switch by using the correct cable type. Re-enable the port if necessary. • Verify that the power supply installed in the switch meets the power requirements of the LEDs and their meanings. ... privileged EXEC command to PoE port, but is connected to check the port error-disabled, disabled, or shutdown status. OL-6336-10 Catalyst 3750 Switch Hardware Installation Guide 3-3 Exchange the suspect module with a straight-through cable was used to connect Cisco pre-standard IP phones and ...