Carvin SL56C Support and Manuals
Get Help and Manuals for this Carvin item
View All Support Options Below
Free Carvin SL56C manuals!
Problems with Carvin SL56C?
Ask a Question
Free Carvin SL56C manuals!
Problems with Carvin SL56C?
Ask a Question
Popular Carvin SL56C Manual Pages
Instruction Manual - Page 1
STUDIO / LIVE SERIES
SL24 SL40 SL56
Owners Manual
Revision 1 76-00024
Instruction Manual - Page 3
...faders. We encourage you to read the manual and if you have questions call and allow for individual bus routing for quick overdubbing while simultaneously setting up the system). Depending upon the ... the tape input signal or the mic input to configure your console for PFL (especially while setting up the stereo control room mix. But, you may decide that is not normally considered. ...
Instruction Manual - Page 4
...YOUR MIXER FOR ANY DAMAGE which CARVIN and the shipping company are not responsible for warranty service if needed in "plain English". It is found, please notify the shipping company and CARVIN...-ship your new CARVlN console will be of the card and return the portion with this manual easy and convenient. We sincerely welcome any questions you find using our equipment while keeping ...
Instruction Manual - Page 5
... position.
some features or setup connections may be needed to...master levels counter clockwise to read the entire manual. After adjusting the corresponding master fader, ... 6 0 10
7/8
5
TAPE
0 10
C PRE FAD w/EQ
7 PAN 8
C
LR
PAN
PK
SOLO
MUTE +12
Set your power supply and zeroing the console, turn up the gain control at the top of the master groups or Left-Right via ...
Instruction Manual - Page 6
Meter Bridge pg 23 9. Block Diagram pg 26 12. General Specifications pg 27 Appendixes B. Console Dimensions pg 34 D. Mixer Overview pg 7 2.... Returns & Tape IN/OUT Auxiliary Send Masters 5. Glossary of Terms pgs 35-37
6 Input Channel Section pg 8 4. Standard Live Mixer Setups . . . . .pg 17 7. Schematics pgs 28-33 C. Power Supply pg 24 10. TABLE OF CONTENTS
Introduction pg 2 a) ...
Instruction Manual - Page 8
... effects unit and to return the effects unit to the units input and the corresponding TS (Tip/Sleeve) plug goes in (depending on channel insert set up the alternate input path in the dual in groups of the channel (post fader) unaffected by the pan or assignments. CHANNEL TAPE IN The...
Instruction Manual - Page 10
...fader tracking sends needed .
0 1 10 PRE 1-2
5
5
0 2 10
See TAPE switch for nominal setting of the channel. Here the alternate input (the input not going to monitor each
5
5
channel, but... The GREEN SOLO LED indicates the solo switch has been pressed on sub mixing. See Standard Live mixer setups for sub-mixing and to prevent input overloading. TAPE 5 - 6 SWITCH The TAPE 5 - 6...
Instruction Manual - Page 12
... the AUX 1-2 masters. SOLO LEVEL The SOLO level controls the volume of both masters.
16. MONO: creates a control room left , the right, or any PAN setting of the SOLO bus heard through the STUDIO outputs. STUDIO LEVEL The STUDIO level adjusts the level of CONTROL ROOM outputs.
Control Masters
13. For...
Instruction Manual - Page 14
...
DIRECT OUT
TAPE
4 BAND CHANNEL EQ
CONTROLS
FADER
AUX SENDS AUX TAPE SWITCHS
In-Line Recording Setup. TAPE IN
The S/L series consoles are both the tracking and mix down (where all
the Auxiliaries...the connections described here can handle a mic input, a direct output to provide the best setup for mix down modes because the TAPE switches re-patch the inputs for tracking (recording ...
Instruction Manual - Page 15
...'s TAPE IN's are receiving the multi-tracks 1-8 outputs and the mixers DIRECT OUT's are setup using a patch bay like the Carvin PB48 patch bay . This allows multiple channels to be recorded to... tracks 1-8. Figure 5-3 shows a simple combination of channels down to track. The setup shows a typical 16 channel recording system. The first 8 channels are used to sub-mix banks of ...
Instruction Manual - Page 17
...5
5
5
5 0 10 6
5
5 0 10 6
5
5 0 10 6
5
now available at the 1-4 send 1/4" outputs. In most sys- These inputs, in set-up requirements and connections, this configu-
0 10 PFL
0 10 PFL
0 10 PFL
0 10 PFL
0 10 PFL
0 10 PFL
0 10 L-R
ration have no EQ, so...cases, the AUX 1-2 sends and AUX 3-4 sends in live mixer setups
The following are made up ). The Auxiliary 1-4 sends are
AUX ...
Instruction Manual - Page 19
...use of a graphic equalizer solves most major monitor feedback problems. Now for the expected stage level of the monitors ...the "front-of-house" rack will be not setup properly for a drum set sound. Figure 6-4 shows a typical live sound ...graphic equalizes for stereo). Also, sub-mixing can help support center clusters, extension speakers for reaching distant listeners and surround...
Instruction Manual - Page 22
... the channels signal path. The insert in full insert mode, the channel is opened up to the input of using the insert jack is not set up position) or the TAPE IN (down position), will be added in the mixdown. The half insertion connects the tip of the plug being inserted...
Instruction Manual - Page 35
... of the mixing console rather than 3dB, expressed in decibels as the PFL feature on the "cue," or making sure the level and EQ are set properly.
Dynamic Microphones Refers to the input of microphones that the dB is usually expressed in Hertz.
Chorusing An effect available in decibel referenced to...
Instruction Manual - Page 36
...wiring tips or call technical support. This is a mono pickup...to ground loops, check your manual for its boost/cut controls with...safety ground to reduce ground loop noise problems.
Ground loop A ground loop occurs...Setting the mic preamp gain correctly is common for your system due to properly set... the EIN (Equivalent Input Noise) A specification that rejects low frequencies.
Highpass filter A...
Carvin SL56C Reviews
We have not received any reviews for Carvin yet.