Carvin MX601 Support and Manuals
Get Help and Manuals for this Carvin item
View All Support Options Below
Free Carvin MX601 manuals!
Problems with Carvin MX601?
Ask a Question
Free Carvin MX601 manuals!
Problems with Carvin MX601?
Ask a Question
Popular Carvin MX601 Manual Pages
Instruction Manual - Page 1
ESCONDIDO, CA 92025 TOLL-FREE: (800)854-2235 CARVIN
MX621 & MX641 RACK MOUNT MIXERS
MX601 SERIES CONSOLE MANUAL
REVISED 2/16/88
1155 INDUSTRIAL AVE.
Instruction Manual - Page 3
... Mixer! * Facts About Use * Precautions * Procedures Before Turning On Unit
SECTION III * Front Panel Features * Rear Panel Features
SECTION IV * Connections to the Unit
SECTION V * Servicing In Your Area * Factory Servicing * Warranty Requirements * Service Authorization Form
SECTION VI " Specifications * Schematic & Technical Information
1-2 3-7
8-17 18 19-21 22-23
Instruction Manual - Page 6
...-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE UNIT TO RAIN, MOISTURE, EXPLOSIVE ATMOSPHERE, OR INSTALL AN IMPROPER FUSE. If you determine (after allowing an appropriate amount of time) that you have received.... If you receive all the items in the event such servicing is necessary. Save your order. It will be that you find some items missing it may take...
Instruction Manual - Page 7
...series mixers are professional rack mountable consoles with built-in two models: MX621 and MX641. PLEASE NOTE: For simplicity, the manual will refer to both the line and mic inputs to ... will allow you to be used at the same time. These controls should accommodate any type of setup hassles. Since the internal power amplifiers are patchable on the front panel, you may be used with...
Instruction Manual - Page 8
... series mixers, are backed by using highly reliable modular connectors allowing a channel to feedback.
Thank you support of your main speakers and achieve the most volume prior to be easily removed for you for servicing or replacement. This equalizer will allow precise adjustments to the MX641 without using up channels. It will allow...
Instruction Manual - Page 9
... in maintaining its best performance and reliability.
1. The wires used for your new mixer will help greatly in series with the hot speaker line) of trouble free performance. Please remember that the A.C. One of the major contributers to offer many years of your speaker cord. RECEPTICLE. lines are not 100% fail...
Instruction Manual - Page 15
... the volume of the signal sent to the problem.
5. These levels will then be due to the internal reverb system and will control the level of a specific range. CHANNEL TONE CONTROLS- The active tone controls... effect.
Any channel volume changes will adjust the overall response of the signal sent to set the level (per channel) of the channel. If you to properly balance the level ...
Instruction Manual - Page 16
The "channel" volume levels will set the relative levels of your effect. It is usually best to operate the Main Volume Level control at the patch section of the MX641) to ...
Instruction Manual - Page 17
.... You may wish to be accessed using a shielded 1/4" shielded type
guitar cord.
This is unassigned and
available to have two different effects at a slightly lower setting than the main mix on the MX641). This will be internally powered and equalized by the channel monitor level control.
This ensures that the EQ...
Instruction Manual - Page 19
...you should then make the appropriate adjustments on each band is listed according to the exact band that setting up your ear. Graphic equalizers are listed as there are more difficult. This is "not" the...will ultimately allow you to use of this point the best way to set your equalizer would be simple--probably more controls than a conventional rotary control three or four band...
Instruction Manual - Page 21
... for the MX601 series consoles are twc. 1/4" phone type speaker output jacks. It is the only place where you read on the MX641 (higher powered) model. source produced by inserting a small screwdriver and moving the switch to cable
3.15 LINE FUSE - These two jacks are wired in the MX641 mixer) to...
Instruction Manual - Page 25
The MX641 model console has dual voltage capability 120V/220V.
If you need to connect a single ended (RCA phono, or 1/4" phone connection)... 1/4" PHONE DIAGRAM RCA TO XLR DIAGRAM
LINE LEVEL OUTPUT OF CONSOLE
TO "LINE IN" OF TAPE DECK
4-18 INPUT-
The color code of the MX601 series mixers. This is provided on your unit. The 3-pin grounded type plug is standard and is as follows:
...
Instruction Manual - Page 27
... component replacement. Under the ONE YEAR WARRANTY, Garvin will ship parts pre-paid to make necessary repairs faster, and for service:
1. IF YOU ELECT TO HAVE YOUR OWN SERVICING DONE, THESE BILLS MUST BE PAID BY THE CUSTOMER. WARNING: TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE TO RAIN, MOISTURE, EXPLOSIVE ATMOSPHERE OR INSTALL AN...
Instruction Manual - Page 28
...repairs in its original carton with the sale or servicing of warranty, you will service the unit, supply all other warranties, expressed or implied. CARVIN WILL NOT PAY FOR PARTS OR SERVICING...or assume for Carvin any horn driver speaker damaged by UPS if ...specifications without notice or obligation.
5.20 Carvin will be charged a modest fee (generally lower
than typical repair...
Instruction Manual - Page 29
TECHNICAL SPECIFICATIONS
Frequency Response Mic or line inputs: 20 Hz-20KHz ±1 dB
Total Harmonic Distortion Mic in ...80 dBv
Master controls nominal w; -75 dBv Channel controls minimum: (non-powered models)
-80 dBv (powered models) Master controls nominal WI -82 dBv one channel set for 40 dB gain. -79 dBv (powered models)
Crosstalk
Adjacent channels: -60 dB at lkHz -50 dB at 10kHz
Common ...
Carvin MX601 Reviews
We have not received any reviews for Carvin yet.