Campbell Scientific CS300 Support and Manuals
Get Help and Manuals for this Campbell Scientific item
View All Support Options Below
Free Campbell Scientific CS300 manuals!
Problems with Campbell Scientific CS300?
Ask a Question
Free Campbell Scientific CS300 manuals!
Problems with Campbell Scientific CS300?
Ask a Question
Popular Campbell Scientific CS300 Manual Pages
CS300 Silicon Pyranometer - Page 2
... of the problem, an RMA number will be issued. will not process any Campbell Scientific, Inc. Campbell Scientific, Inc.
Products may cause health or safety concerns for special, indirect, incidental, or consequential damages. Please write this form. The form is in countries served by Campbell Scientific, Inc. This warranty shall not apply to repairing or replacing (at www...
CS300 Silicon Pyranometer - Page 3
... General Description 1 2. CM225 Pyranometer Mounting Stand and CM202 Crossarm 3 3-2. 015ARM Pyranometer Mounting Arm 3 4-1. CS300 Schematic 4
Tables
4-1. Connections to specific sections.
1. Use the Adobe Acrobat® bookmarks tab for links to Campbell Scientific Dataloggers 4 5-1. CS300 Table of Contents
PDF viewers note: These page numbers refer to the printed version of...
CS300 Silicon Pyranometer - Page 5
The CS300 should not be set to zero in the datalogger program. Negative values may read slightly negative incoming solar radiation....CS300 may be used under natural sunlight to accurately measure sun plus sky radiation (300 to voltage by RF noise passing through the photo-diode. This negative signal is calibrated so that all sensors have the same output sensitivity. Specifications...
CS300 Silicon Pyranometer - Page 6
...their cable that it is not critical for the accuracy of the measurement.
Tools required for installation on the underside of three mounting configurations (see Figures 3-1 and 3-2). However, pyranometers mounted ...
NOTE
Remove the red cap after installing the sensor. Installation
The CS300 should be mounted such that contains a circuit board (located 18" from direct sunlight....
CS300 Silicon Pyranometer - Page 7
CM225 Pyranometer Mounting Stand and CM202 Crossarm
CS300 Pyranometer PN 18356 Base 015ARM
FIGURE 3-2. 015ARM Pyranometer Mounting Arm
3 CS300 Pyranometer
CS300 Pyranometer PN 18356 Base
CM225 Stand
CM200 Series Crossarm
FIGURE 3-1.
CS300 Silicon Pyranometer - Page 8
... that use Edlog include CR7, CR10(X), CR510, and CR23X. CS300 Pyranometer
4. CS300 Schematic
Connections to read this sensor can be wired to use CRBasic include the CR200(X), CR800, CR850, CR1000, CR3000, CR5000, and CR9000(X).
Single-Ended RED Analog Input
BLACK Ground/AG
500 to Campbell Scientific Dataloggers
Color Red Black
Clear
Wire Label Signal Signal...
CS300 Silicon Pyranometer - Page 9
CS300 Pyranometer
Solar radiation can be set to zero before being processed. TABLE 5-1. If the sensor or datalogger is given ... TABLE 5-2. Wiring for the examples is located in the example programs.
5.1 Example Programs
The following programs measure the CS300 every 10 seconds and convert the mV output to zero before being processed. Negative values should be recorded as shown...
CS300 Silicon Pyranometer - Page 10
...code 0 or 25 for > 1200 w/m2 intensities. For the
SE Channel Loc [ SlrW ]
CR10X, use 500 mV range for the CR7 and 21X,
1000 mV range for a 10 second scan rate SlrMJ=SlrW*0.00005
'Convert mV to MJ/m² for the CR23X.
Multiplier
Offset
6 CS300...Program BeginProg
Scan(10,Sec,1,0)
'Measure CS300 Pyranometer VoltSe (SlrW,1,mV250,1,1,0,_60Hz,1.0,0)
'Set negative values to zero If SlrW ...
CS300 Silicon Pyranometer - Page 11
...[ SlrW ]
11: If time is (P92)
1: 0
Minutes (Seconds --) into a
2: 1440
Interval (same units as above)
3: 10
Set Output Flag High (Flag 0)
12: Set Active Storage Area (P80)
1: 1
Final Storage Area 1
2: 102
Array ID
CS300 Pyranometer 7 Set negative values to zero
2: If (XF) (P89)
1: 1
X Loc [ SlrW ]
2: 4
<
3: 0
F
4: 30
Then Do
3: Z=F x 10^n (P30)
1: 0
F
2: 0
n, Exponent of...
CS300 Silicon Pyranometer - Page 12
.... Be careful not to record total flux using the IEEE4 or long data format. Instruction 78 is used to switch to arrive at a output interval flux density. For Edlog...is desired in kJ m-2 and assume an irradiance of 0.5 kW m-2, the maximum low resolution output limit will be removed. CS300 Pyranometer
13: Real Time (P77)
1: 1220
Year,Day,Hour/Minute (midnight = 2400)
14: Resolution (P78)
1: ...
CS300 Silicon Pyranometer - Page 13
Troubleshooting
Symptom: -9999 or radiation values around 0
1. Disconnect the sensor leads from the datalogger and use a DVM to Campbell Scientific, Inc.
Obtain an RMA number before returning the CS300 to check the voltage between the red (+) and the black (-) wires. Check that the sensor is properly leveled.
2. No voltage indicates a problem with either the photodiode or...
Campbell Scientific CS300 Reviews
We have not received any reviews for Campbell Scientific yet.