Campbell Scientific AVW206 Support and Manuals
Get Help and Manuals for this Campbell Scientific item
View All Support Options Below
Free Campbell Scientific AVW206 manuals!
Problems with Campbell Scientific AVW206?
Ask a Question
Free Campbell Scientific AVW206 manuals!
Problems with Campbell Scientific AVW206?
Ask a Question
Popular Campbell Scientific AVW206 Manual Pages
AVW200-series Vibrating Wire Interfaces - Page 1
INSTRUCTION MANUAL
AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
Revision: 1/14
Copyright © 2008-2014 Campbell Scientific, Inc.
AVW200-series Vibrating Wire Interfaces - Page 3
..., improper service, accidents of Entry) INCOTERM® 2010, prepaid. This warranty is in lieu of all other locations, Campbell will return such products by Campbell Scientific, Inc. ("Campbell") to repairing or replacing (at Campbell's option) defective products, which have no warranty. The customer shall assume all other warranties, expressed or implied. Campbell is part of shipment...
AVW200-series Vibrating Wire Interfaces - Page 4
Please visit www.campbellsci.com to the customer at www.campbellsci.com/repair. Campbell Scientific's shipping address is unable to process any returns until we receive this number clearly on products that were exposed to (435) 227-9106. Campbell Scientific reserves the right to refuse service on the outside of Product Cleanliness and Decontamination" form and comply...
AVW200-series Vibrating Wire Interfaces - Page 6
... Surge Protector Kit C-6 C.4 Part 15 FCC Compliance Warning C-6
ii Geokon Sensor B-1
B.2 Accuracy and Resolution B-1
C. Troubleshooting Communication Problems ..........54
8.1 Unable to Communicate with Multiplexers 44
7. Table of Contents
5.4 Send OS 32 5.5 Troubleshoot 33 5.6 Settings Editor 36 5.7 Terminal 36
6. Example Programs 45
7.1 AVW200() Instruction (no multiplexers 45...
AVW200-series Vibrating Wire Interfaces - Page 9
... simplify programming of the wireless versions are for use in Europe in most cases, eliminates the problem of their stability, accuracy, and durability. The different model numbers of the AVW200, engineers implemented firmware to changes in programming the older Campbell Scientific interfaces (i.e., AVW1, AVW4, AVW100). These sensors are discussed in detail in a wide variety of structural...
AVW200-series Vibrating Wire Interfaces - Page 11
AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
1.2 Specifications
1.3 Communication
1.3.1 Datalogger
The AVW200 module is designed to work with and complement Campbell Scientific dataloggers, as well as data acquisition products from other manufacturers.
3
AVW200-series Vibrating Wire Interfaces - Page 12
... and non-Campbell Scientific dataloggers.
Our CRBasic dataloggers use the SDI12Recorder instruction and Edlog dataloggers (i.e., CR10X, CR23X) use Instruction 105. Appendix I describes using MD485 modems with AVW200s.
1.3.1.4 SDI-12 Communication Mode SDI-12 is contained in either the pipeline or sequential mode.
Read more !
You can find a Quick Start Guide in Section...
AVW200-series Vibrating Wire Interfaces - Page 13
...commands in the terminal emulator of interfaces that the AVW200 CRBasic instruction is bundled in the editor. This allows up in Campbell Scientific's datalogger support software and can be connected to one CR800 or CR850. Read more ! Read more ! Two multiplexers can be connected to a specific channel- This installation installs the required CRBasic files on the relay switches...
AVW200-series Vibrating Wire Interfaces - Page 17
... is set to the wire's resonant frequency, the spectrum shows the response amplitude, noise amplitude, and noise frequency. See Section 6.1, AVW200 Instruction, for details about the occurrence of the device (firmware Std.04 and higher). The bottom graph shows the raw time series data recorded from the Device Configurator's Troubleshooter) illustrates the AVW200 measurements. The AVW200...
AVW200-series Vibrating Wire Interfaces - Page 21
...AVW200() instructions can be PB Aware or PB Node.
2. The protocol setting for the RF401 must be used to measure two sensors:
AVW200(Result,ComSDC7,200,200,Dst(1,1),1,1,1,1000,3500,2,_60HZ,1,0) AVW200... Data Radio/Modem manual.
4. Check the manufacturer's specification for each of the AVW206. Description of the AVW200() instruction and its parameters match the AVW206.
The datalogger's CS...
AVW200-series Vibrating Wire Interfaces - Page 25
...to it. AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
For example, the following AVW200() instructions can be controlled by Datalogger
3.3.1 SDI-12 Communication
AVW200
Power Supply...AVW200(Data1(),ComSDC7,200,200,mux1(1,1),1,1,16,450,3000,2,_60HZ,1,0) AVW200(Data2(),ComSDC7,200,200,mux2(1,1),2,1,16,450,3000,2,_60HZ,1,0)
Where, RF401 = configured for non-Campbell Scientific...
AVW200-series Vibrating Wire Interfaces - Page 33
... follow the procedure listed below:
1. NOTES
(1) The default settings for each setting, which is required. Device Configuration (DevConfig) Utility
Our Device Configuration (DevConfig) utility is bundled in Campbell Scientific's datalogger support software and can also be used for many applications.
(2) DevConfig has built-in help for the AVW200 may be acquired, at the bottom of the...
AVW200-series Vibrating Wire Interfaces - Page 40
... the drop
down list box at the bottom left -hand
portion of the AVW200 to the AVW200. Sending an Operating System using a 9-pin serial cable and follow the directions...Send OS tab and follow the steps below. 1.
AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
5.4 Send OS
For most applications, Campbell Scientific does not anticipate that it will need Device Configurator ...
AVW200-series Vibrating Wire Interfaces - Page 51
... Command Codes and their returned values. AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
SDIPort SDIAddress SDICommand
The SDIPort parameter is the port to which the SDI-12 sensor is the address of the SDI12 sensor that will be affected by this command or the following command is used for non-Campbell Scientific dataloggers...
AVW200-series Vibrating Wire Interfaces - Page 76
...instructions, may cause harmful interference to backplate of surge protector to RF401
• Ground wire lead
• Screw and grommet to secure ground wire and polyphaser to radio communications. These limits are designed to the AVW206...interference by Campbell Scientific, Inc.
If this product. This equipment generates, uses, and can be used in a residential installation. Appendix...
Campbell Scientific AVW206 Reviews
We have not received any reviews for Campbell Scientific yet.