Brother International SB3734T Support and Manuals
Get Help and Manuals for this Brother International item
This item is in your list!
View All Support Options Below
Free Brother International SB3734T manuals!
Problems with Brother International SB3734T?
Ask a Question
Free Brother International SB3734T manuals!
Problems with Brother International SB3734T?
Ask a Question
Brother International SB3734T Videos
Popular Brother International SB3734T Manual Pages
Operation Manual - Page 2
... machine - Fully plug the machine directly into any other user servicing adjustments mentioned in this manual before cleaning. Use only mild soaps or detergents to persons.
1. To repair or adjust the machine
If the machine breaks down or needs adjustment, first follow the troubleshooting table to be followed, including the following circumstances: - Do not...
Operation Manual - Page 3
...servicing the sewing machine, or when removing covers, the machine or the electrical set must be removed from 8 years and above and persons with this sewing machine unattended, the main power and light switch of replacing...Never use of experience and knowledge if they have been given supervision or instruction concerning use by children aged from the socket-outlet. Children shall not ...
Operation Manual - Page 4
...in the motor are part of this booklet.
...is quite fast compared to the normal operating speed of service. and CANADA only) 3
[Product code: 884-B02] [Product code: 884-B03]
2 Continuous operation of the sewing machine...that you need more information regarding the use product.
CAUTION
When threading or replacing needle, the main power and light switch of your machine, your nearest...
Operation Manual - Page 5
...Names of parts and ..., One needle (Three thread 12 Needle...13 Removing/ Installing the needle 13
Chapter 2 : Preparation before threading 14...Troubleshooting...26
Chapter 7: Maintenance...27 Cleaning...27 Oiling ...27
Chapter 8: Introduction of optional feet 28 Blind stitch foot...28 Taping foot...30 Pearl sequence foot...31 Piping foot...32 Gatheing foot...33
Specifications...34
Setting...
Operation Manual - Page 6
... length adjustment dial
4
* The product code is shown on the side and back) Chapter 1 Names of parts and their functions
Inside of the front cover L Thread guide M Lower looper threading lever N Thread take.... : Needle set, : Stitch finger (when removed, see CHAPTER 5 "Narrow overlock/ Rolled hemming stitch"), : Tweezers, : Hexagonal driver
* Air openings (on the machine rating plate.
Operation Manual - Page 7
...authorized Brother dealer.
* The product code is shown on the machine model. ...code 884-B03
LP
LS
9 3
4
0 5
* The part code differs depending on the color of the trim trap. Included accessory
1 Soft cover: X77871000 2 Accessory bag: XB2297001 3 Tweezers: XB1618001 4 Thread net (4): X75904000 5 Thread spool cap (4): X77260000 6 Cleaning brush: X75906001 7 Hexagonal driver: XB0393001 8 Needle set...
Operation Manual - Page 12
.... 2 Pink marked tension disc is for right needle. 3 Green marked tension disc is for upper looper. 4 Blue marked tension disc is insufficient, select a different tension setting.
5
4
3
Tension selection mark
1 For heavy tension: 4 to 7 2 For light tension: 4 to 2 3 For medium tension: 5 to 3
If you cannot find the correct tension, refer to the...
Operation Manual - Page 23
... remove work . If feeding for consistent cutting of the fabric seams. The scale of Seam Allowance Guide shows 9.5, 12.7, 15.9, and 25.4 mm (3/8, 1/2, 5/8, and 1 inches) when the stitch width dial is set to depress the foot controller slightly and chain off . Holding all threads out about 15 cm (6 inches) behind the presser...
Operation Manual - Page 26
... on the inside of the front cover.
[Product code: 884-B02]
5. NOTE: Make sure to the "R" position. Storage for rolled hemming stitch: R).
3
Selection mark
[Product code: 884-B03]
* The product code is provided on the machine rating plate. Adjust the stitch width dial up to install stitch finger when sewing regular overlock stitches.
4. Adjust...
Operation Manual - Page 28
.... (See page 13.)
3. Wrong needle used
Use correct needle. 130/705H - Needles incorrectly installed
Install needles correctly. (See page 13.)
3. and remove tangled thread.
3. Needles incorrectly installed
Install needles correctly. (See page 13.)
5. Needle bent, or needle tip blunt Replace with new needle. (See page 13.)
2. Improper threading
Thread correctly. (See pages 15-18...
Operation Manual - Page 30
...optional feet
CAUTION
Turn off the machine while replacing the presser foot.
5. Turn the hand wheel...guide, a piece of the same fabric should be used for 3 thread overlock stitch with one needle in the left in such a way that the line on the hand wheel is aligned to do a sewing test.
8.
When done correctly, this foot is used to the line on a project. Recommended settings...
Operation Manual - Page 31
...stitch".) 3. If you sew with the adjusting screw so that the needle moves down the fold.
9. Set up the machine for narrow overlock
stitching. (Refer to the line on the machine (see CHAPTER 1... the fabric with a fabric pencil as shown in two
4. To adjust the position of the fabric guide, a piece of hand wheel").
5. Draw equally spaced lines on the fabric with the folded edge ...
Operation Manual - Page 32
... of tapes / elastics will be sewn.
- Usage of the elastic Usage of hand wheel"). 4. Flip open the tape guide 1, then set the elastic / tape
3 Adjusting screw 4 Fabric guide
9. By turning the screw backward the stitch guide will go to the right. Attatching tapes is very useful for sewing cuffs, neckline and so on the...
Operation Manual - Page 33
... according to 1.5mm.
4.
Place the pearl through the tunnel.
2. Set the stitch length control lever.
- Use the screw 2 and adjust ...guide 1.
3. Tie both end of guide tunnel 3. Tapes: between folded edge needle so that it becomes 1mm to the length as follows:
Needle thread: slightly decrease Over looper thread: slightly decrease Under looper thread: slightly increase
How to set...
Operation Manual - Page 34
... and put the piping tape into the groove of material. Place fabric with cutting the excess part.
5 ~ 6mm 5 ~ 6mm
32
Piping sewing is useful to adjust the machine
1.
Adjust... CHAPTER 5 "Stitch Selection").
3mm
3mm
How to 6mm
3.
Set stitch width at the edge of piping foot and start sewing.
Carefully guide the fabric and piping tape by hands during sewing.
2. The...
Brother International SB3734T Reviews
Do you have an experience with the Brother International SB3734T that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Brother International yet.
Earn 750 points for your review!