H243 LCD Monitor Service Guide
Page 5
... note 2 Operating Storage : -20°C to 60°C : 5% to 90% 10000 ft (Ta=50, t=24h) 30000 ft (Ta=30, t=24h ) Acer -LCD-H243H Note 1: Temperature and relative humidity range must withstand 8KV for contact discharge and 15KV for air discharge of Electrostatic Discharge and meet the standard of ... displaying an all WHITE field at cold-start , 25°C, DC output full-loading and 100Vac input b. 60A max at mid Brightness and Contrast settings. 3. The LCD panel life which is from 50Hz to panel limited Note 2: Altitude spec must not over panel spec. 2.2 Safety, EMC, Ergonomics...
... note 2 Operating Storage : -20°C to 60°C : 5% to 90% 10000 ft (Ta=50, t=24h) 30000 ft (Ta=30, t=24h ) Acer -LCD-H243H Note 1: Temperature and relative humidity range must withstand 8KV for contact discharge and 15KV for air discharge of Electrostatic Discharge and meet the standard of ... displaying an all WHITE field at cold-start , 25°C, DC output full-loading and 100Vac input b. 60A max at mid Brightness and Contrast settings. 3. The LCD panel life which is from 50Hz to panel limited Note 2: Altitude spec must not over panel spec. 2.2 Safety, EMC, Ergonomics...
H243 LCD Monitor Service Guide
Page 6
... Video Resolution Video input level Warm-up time : 25 ± 5°C : white : 1920 x 1080 : 700 mV ± 2% : 30 minutes Set brightness control and also contrast control at maximum, to measure the screen center, the light output shall BL ≥ 240 cd/m2 (as panel spec). 3.2 ...verify specifications in this section shall be performed under the following standard conditions unless otherwise noted. Max. Acer 75% (DC output full loading and nominal AC input voltage range) Acer -LCD-H243H Ripple and Noise Total composite ripple and noise less than 800mV for +25V output, and less ...
... Video Resolution Video input level Warm-up time : 25 ± 5°C : white : 1920 x 1080 : 700 mV ± 2% : 30 minutes Set brightness control and also contrast control at maximum, to measure the screen center, the light output shall BL ≥ 240 cd/m2 (as panel spec). 3.2 ...verify specifications in this section shall be performed under the following standard conditions unless otherwise noted. Max. Acer 75% (DC output full loading and nominal AC input voltage range) Acer -LCD-H243H Ripple and Noise Total composite ripple and noise less than 800mV for +25V output, and less ...
H243 LCD Monitor Service Guide
Page 10
... "F" for DC power on the keypad position 3 OSD Timeout --- --- 10~120 10 Wide Mode Setting DDC/CI Full Aspect ON Full ON 9 H. Position 0~100 50 V. Clock 0~100 50 (1) Warm --- --- --- V. Acer FACTORY MODE ● Acer -LCD-H243H Press [e], and then press [POWER] for entering factory mode. 5.4 OSD Structure The On-Screen Display...
... "F" for DC power on the keypad position 3 OSD Timeout --- --- 10~120 10 Wide Mode Setting DDC/CI Full Aspect ON Full ON 9 H. Position 0~100 50 V. Clock 0~100 50 (1) Warm --- --- --- V. Acer FACTORY MODE ● Acer -LCD-H243H Press [e], and then press [POWER] for entering factory mode. 5.4 OSD Structure The On-Screen Display...
H243 LCD Monitor Service Guide
Page 14
Acer Acer -LCD-H243H Note: if programming fails or success rate is not high, click "Config" and adjust its speed in "E2PROM DEVICE SETTING" After connecting, AC ON, DC ON OK Open ISP program OK Choose manufacturer and model of FW IC OK LOAD FW software OK Click Connect and enter ISP MODE OK $MJDL"650BOE36/GPS CFHJOOJOHQSPHSBNNJOH OK Turn off power if programming is OK ³Flowing chart NG Choose Config and adjust programming 13
Acer Acer -LCD-H243H Note: if programming fails or success rate is not high, click "Config" and adjust its speed in "E2PROM DEVICE SETTING" After connecting, AC ON, DC ON OK Open ISP program OK Choose manufacturer and model of FW IC OK LOAD FW software OK Click Connect and enter ISP MODE OK $MJDL"650BOE36/GPS CFHJOOJOHQSPHSBNNJOH OK Turn off power if programming is OK ³Flowing chart NG Choose Config and adjust programming 13