Troy-Bilt TB625 Support Question
Troy-Bilt TB625 Support Question
Find answers below for this question about Troy-Bilt TB625.Need a Troy-Bilt TB625 manual? We have 1 online manual for this item!
Question posted by Ibbroman on April 25th, 2015
Can You Replace The Bump Feed String Head With A Fixed Line Head?
The person who posted this question about this Troy-Bilt product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by TechSupport101 on April 27th, 2015 4:21 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,315
Member since:
May 24th, 2013 Points: 12,171,315
Related Troy-Bilt TB625 Manual Pages
Operation Manual - Page 1
...at the time of authorized service dealers near you. When servicing, use only identical replacement parts.
769-08457 / 02
All information, illustrations, and specifications in Canada. ... the right to obtain a list of printing. Operator's Manual
Electric Start Capable 4-Cycle Trimmer
TB625 EC
TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 Specifications 5 Assembly 6 Oil...
Operation Manual - Page 2
...area.
• Be aware of risk of injury to the head, hands and feet.
• Carefully inspect the area before... be constructed, equipped and maintained for later use the trimming line described in place. • Avoid creating a source of ...carefully. Replace damaged parts. Never use of the unit.
• Do not operate this manual. Remove rocks, broken glass, nails, wire, string and ...
Operation Manual - Page 3
.... SAVE THESE INSTRUCTIONS
3 Secure hair above shoulder level.
• The cutting head shield must be in daylight or good artificial light.
• Avoid accidental starting...lines extended and the proper line installed. The operator and unit must always be performed by a authorized service dealer.
• Before inspecting, servicing, cleaning, storing, transporting or replacing...
Operation Manual - Page 4
.... These parts get burned. Wear eye protection meeting current ANSI Z87.1 standards and ear protection when operating this unit. Failure to do not touch the line cutting blade.
4 • SAFETY & INTERNATIONAL SYMBOLS •
This operator's manual describes safety and international symbols and pictographs that fuel containing
greater than 10% ethanol will...
Operation Manual - Page 5
... and light weeds. • Edging • Decorative trimming around trees, fences, etc. Other optional accessories may be used with cutting head, cutting head shield and handle 13 - 14 lbs. (5.9 - 6.4 kg) Trimmer Mechanism Bump Head Trimming Line Diameter 0.095 inches (2.41 mm) Cutting Path Diameter 17 in . (0.635 mm) Spark Plug Champion® RDZ4H or equivalent...
Operation Manual - Page 6
... in the operating position (Fig. 14), move
the handle to align the hole on the cutting head shield with this unit.
1. Tighten the bolt with a 3/8" socket until the handle is not ...place (Fig. 2).
Tighten the bolt with a 3/8" socket (Fig. 3). 2. ASSEMBLY
INSTALLING THE CUTTING HEAD SHIELD
WARNING: To prevent serious personal injury, never
operate the unit without a hole) on the mount...
Operation Manual - Page 7
...
straight out of various optional attachments. NOTE: Do not tighten the nut (Fig. 5).
Follow all safety information contained within.
NOTE: Aligning the release button with a string trimmer attachment, lock the release button into the primary hole (Fig. 6) and the knob (Fig. 4) is securely tightened.
Using the wrong hole could lead to...
Operation Manual - Page 12
... the ground (Fig. 15) while operating the unit at a 30° angle to release line in the operating position (Fig. 14). • Hold the shaft grip with a Bump Head.
NOTE: Some line breakage will make the unit overheat. Trimming line can be released from the operator. • Do not trim wet grass or weeds. CAUTION...
Operation Manual - Page 13
... you are of equal length. 5. Refer to Removing Old Trimming Line and Obstructions.
2. REPLACING THE TRIMMING LINE
Only use metal-reinforced line, wire, chain or
rope. These can break off and become...a complete listing of new trimming line. 3. Turn the bump knob counterclockwise to prevent the unit from the exit eyelet. Push
the line through the cutting head until a few inches protrude from...
Operation Manual - Page 14
... oil level before each use a flashlight if necessary. Inspecting the Oil Level Window 1. The cutting head shield should fill the window approximately halfway (Fig. 21).
Look into the holes.
The importance of...Oil Level
Fig. 21
Spool Cover Inner Reel Outer Spool
O-Ring
14 Remove any old trimming line and/or obstructions from entering the oil fill hole. 2. If the oil level is in...
Operation Manual - Page 15
Allow ample time for complete drainage. oz (60 ml) fill line indicated on the oil fill plug (Fig. 21). Wipe up any oil that may have spilled. 5.... Squeeze the air filter to the left. Swing the air filter cover to spread and remove excess oil. 6. Fig. 22
Fill Line
Fig. 23
Hole
Air Filter Housing
Tab
Air Filter Cover
Air Filter
Fig. 24
Cover Screw
15 Unscrew the oil fill plug....
Operation Manual - Page 16
...plug
electrodes. Inspect the spark plug. Idle Speed Screw Fig. 25
0.025 in the cylinder head. Stop the engine and allow it clockwise until the engine idles smoothly (Fig. 25). ...engine hesitates or stalls on acceleration • there is cracked, fouled or dirty, replace it from the cylinder head with replacement part #753-05784, a Champion RDZ4H or an equivalent spark plug.
4. Do not...
Operation Manual - Page 17
... oil from the carburetor.
3. Pull the starter rope slowly to clean the outside of any loose or damaged parts. Reinstall the spark plug.
4. Repair or replace damaged parts and tighten loose screws, nuts or bolts. Change the oil.
Use a small brush to distribute the oil. Do not use fuel that contain...
Operation Manual - Page 18
... fresh fuel Clean or replace the air filter Replace the spark plug
Stop the engine and clean the cutting head Refill the cutting head with new line Rewind the line Clean the inner reel and outer spool Open the cutting head and remove the welded section Rewind the line Stop the unit, push the bump knob and pull the...
Operation Manual - Page 20
... limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for rental expenses to temporarily replace a warranted product. (Some states do... use the product. Tune-ups - Damage resulting from state to state. Bump Knobs, Outer Spools, Cutting Line, Inner Reels, Starter Pulley, Starter Ropes, Drive Belts, Saw Chains, ...
Similar Questions
Pull String
how do I replace the pull string on my Troybiltiller ?
how do I replace the pull string on my Troybiltiller ?
(Posted by gregschaffer67 3 years ago)
How Do I Remove The Cutting Head Of The Tb625 Ec Trimmer
head removal instructions.
head removal instructions.
(Posted by Anonymous-150877 8 years ago)
How To Remove Full String Head From Tb625ec
I need to remove the complete string head, how do I do it?
I need to remove the complete string head, how do I do it?
(Posted by denniscmalinowski 9 years ago)