Troy-Bilt TB625 Support Question
Troy-Bilt TB625 Support Question
Find answers below for this question about Troy-Bilt TB625.Need a Troy-Bilt TB625 manual? We have 1 online manual for this item!
Question posted by beth4467 on June 25th, 2015
How To Replace Cutting Head
How do I remove the cutting head?
Current Answers
Answer #1: Posted by waelsaidani1 on June 26th, 2015 4:40 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,787
Member since:
May 12th, 2013 Points: 19,501,787
Hello replacement instructions available here: http://homeguides.sfgate.com/replace-trimmer-head-troy-bilt-101771.html
Related Troy-Bilt TB625 Manual Pages
Operation Manual - Page 1
...be performed by an authorized and approved service dealer. When servicing, use only identical replacement parts.
769-08457 / 02
All information, illustrations, and specifications in this unit,...MTD SOUTHWEST INC, All Rights Reserved.
01/13 Operator's Manual
Electric Start Capable 4-Cycle Trimmer
TB625 EC
TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 Specifications 5 Assembly 6 ...
Operation Manual - Page 2
... at risk from the unit immediately, before starting the unit. Remove rocks, broken glass, nails, wire, string and other reproductive ....
• Be aware of risk of injury to the head, hands and feet.
• Carefully inspect the area before... constructed, equipped and maintained for fuel leaks. Replace parts that it requires replacement, ask your state or local authorities for spilled...
Operation Manual - Page 3
... by a authorized service dealer.
• Before inspecting, servicing, cleaning, storing, transporting or replacing any other parts or accessories could block moving parts. Keep a firm grip on steep slopes... cutting head remains stationary when the engine is dusty.
• Wear heavy long pants, boots, gloves and a long sleeve shirt. Be in place while operating the unit. Carefully remove ...
Operation Manual - Page 4
... injury. Use a full face shield when needed.
• UNLEADED FUEL Always use clean, fresh unleaded fuel.
• OIL Refer to do not touch the line cutting blade.
4 When turned off they remain hot for complete safety, assembly, operating and maintenance and repair information.
These parts get burned. To prevent serious injury...
Operation Manual - Page 5
.../Off Switch
Muffler
Spark Plug
Starter Rope Grip
Primer Bulb
Fuel Cap
Handle Shaft Housing
Air Filter Cover
Throttle Control
Choke Lever
Cutting Head
Coupler
Cutting Head Shield
Oil Fill Plug
Line Cutting Blade
SPECIFICATIONS*
Engine Type Air-Cooled, 4-Cycle Displacement 30 cc (1.83 cu. We reserve the right to make changes at the time...
Operation Manual - Page 6
... that provides the best grip. Screw the wing nut onto the square bolt until the cutting head shield is not installed. Tighten the bolt with this unit.
1. Loosen the bolt with a 3/8" socket until the handle is secure.
Remove the wing nut and washer from the end of shaft and shield equipped with a 3/8" socket...
Operation Manual - Page 7
...is securely tightened.
Turn the knob counterclockwise to the unit, shut the unit off before removing or installing an attachment. WARNING: Before using any attachment, read and
understand the manual ... will help installation (Fig. 5). 3. CAUTION: Before operating the unit, make installing or removing the attachment easier, place the unit on the ground or on a work bench. Using ...
Operation Manual - Page 8
... to the Maintenance Schedule. NOTE: This unit comes with gasoline. 6. Unscrew the top of oil. 1. Cut the tip off the funnel
spout (Fig. 7). 3. This unit has a four-
Change the oil according...
Fig. 8
8 ADDING OIL: INITIAL USE
WARNING: OVERFILLING THE CRANKCASE MAY
CAUSE SERIOUS PERSONAL INJURY. Remove the paper seal. cycle engine. OIL AND FUEL
USING THE RIGHT OIL
Use a high-quality SAE...
Operation Manual - Page 9
...fresh, clean unleaded gasoline. Never operate the unit without the fuel cap securely in a clean, well ventilated outdoor
area. Remove the fuel cap. 3. Wipe up any spilled fuel immediately. Reinstall the fuel cap. 6. Alcohol-blended fuel absorbs water....Ignited
vapors may have spilled. 5. NOTE: Do not overfill the tank. 4. WARNING: Remove the fuel cap slowly to the unit's fuel tank.
Operation Manual - Page 11
... to Position 2, and run the unit for 2-5 minutes, or as needed .
Run the electric start accessory for more information. Continue to squeeze the throttle control. Remove the electric start after a few attempts, move the choke lever to Position 3 and squeeze the throttle control. The unit may be used during this time...
Operation Manual - Page 12
...inches (38 mm) of injury when operating this unit.
• Stand in the cutting head shield will cut thick vegetation • Forcing the line into objects such as walls or fence posts
...grass without stopping the engine. CAUTION: Do not remove or alter the line cutting blade
assembly. TIPS FOR BEST TRIMMING RESULTS • Keep the cutting head parallel to the ground (Fig. 16).
12
Fig...
Operation Manual - Page 13
...Cut one 20 foot (6 m) length of terms and coverage for the emissions control devices, such as the spark arrestor, muffler, carburetor, etc. Turn the bump knob counterclockwise to an MTD authorized service dealer. Refer to Removing Old Trimming Line and Obstructions.
2. REPLACING...Spark Plug.
Push
the line through the cutting head until about these required maintenance procedures at 38...
Operation Manual - Page 14
...Oil 1. Unscrew the oil fill plug. 3. Add oil to prevent debris
from the cutting head. 1. Reinstall the oil fill plug. CHECKING THE OIL LEVEL
WARNING: OVERFILLING THE CRANKCASE MAY...Firmly press in place on the cutting head (Fig. 19). 2. Remove any old trimming line and/or obstructions. 4.
Removing Old Trimming Line and Obstructions If necessary, remove any old trimming line and/or ...
Operation Manual - Page 15
...not covered by the product warranty. Unscrew the oil fill plug. 3. Reinstall the oil fill plug.
Remove the air filter from the air filter housing (Fig. 24).
2. Lightly coat the air filter with ...filter cover to secure the air filter cover (Fig. 24). Tighten the cover screw to the left. Remove the air filter cover from the air filter housing (Fig. 24). 3. Wash the air filter in ...
Operation Manual - Page 16
...If the engine is cracked, fouled or dirty, replace it from the cylinder head with a 5/8-inch socket, turning it to :...Tighten the spark plug with a 5/8-inch socket, turning counterclockwise. Remove the spark plug from the spark plug.
2. Reattach the spark... over tighten.
6. ADJUSTING THE IDLE SPEED
WARNING: The cutting head may spin during idle speed
adjustments. Wear protective clothing and...
Operation Manual - Page 17
...as pine and lemon, and solvents such as kerosene, can damage plastic. Change the oil.
Remove the spark plug and put 5 drops of any moisture with the engine at the top. ... • Store the unit out of the reach of the oil from the carburetor.
3. Repair or replace damaged parts and tighten loose screws, nuts or bolts. Short-term Storage (1-2 weeks)
1. Long-term ...
Operation Manual - Page 18
... cutting head and remove the welded section Rewind the line Stop the unit, push the bump knob and pull the line until 4 inches (102 mm) is outside of the cutting head
THE CUTTING LINE ADVANCES UNCONTROLLABLY There is oil, cleaner or lubricant in the cutting head
Clean and thoroughly dry the cutting head
If further assistance is extended
Clean or replace...
Operation Manual - Page 20
...as a gift. Damage resulting from the date of export distribution. Bump Knobs, Outer Spools, Cutting Line, Inner Reels, Starter Pulley, Starter Ropes, Drive Belts, Saw Chains, Guide Bars,
...property arising out of any Troy-Bilt Product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for a listing in the...
Similar Questions
How Do I Replace The Primer Bulb On Tb625 Ec
How do I get the cover off a Troy Bilt TB625 EC Trimmer so I can replace the Primer bulb
How do I get the cover off a Troy Bilt TB625 EC Trimmer so I can replace the Primer bulb
(Posted by Myers8708 2 years ago)
How Do I Change Cutting Head On A Troybilt Tb625ec?
I can't figure out how to remove the old cutting head.
I can't figure out how to remove the old cutting head.
(Posted by dougclapp24 7 years ago)
Replace Trimmer Head
I want to replace the trimmer head with an ugly head. The nuts provided in the ugly head package do ...
I want to replace the trimmer head with an ugly head. The nuts provided in the ugly head package do ...
(Posted by ipferrara 10 years ago)
Remove The Cutting Head
I want to know how to remove the cutting head of TB2044XP trimmer
I want to know how to remove the cutting head of TB2044XP trimmer
(Posted by jthannikary 10 years ago)