Troy-Bilt TB625 Support Question
Troy-Bilt TB625 Support Question
Find answers below for this question about Troy-Bilt TB625.Need a Troy-Bilt TB625 manual? We have 1 online manual for this item!
Question posted by denniscmalinowski on May 25th, 2014
How To Remove Full String Head From Tb625ec
I need to remove the complete string head, how do I do it?
Current Answers
Related Troy-Bilt TB625 Manual Pages
Operation Manual - Page 1
Operator's Manual
Electric Start Capable 4-Cycle Trimmer
TB625 EC
TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 Specifications 5 Assembly 6 Oil and Fuel 8 Starting and Stopping 10 Operation 12 Maintenance 13 Cleaning and Storage ...
Operation Manual - Page 2
... aware of risk of injury to the head, hands and feet.
• Carefully inspect the area before filling the tank. Remove rocks, broken glass, nails, wire, string and other reproductive harm. WARNING: Signals...and safety instructions.
Make sure all adjustments or repairs before starting the engine. Never remove the fuel tank cap or add fuel when the engine is hot.
Forest Land ...
Operation Manual - Page 3
... not operate the unit with both hands when operating. Carefully remove vegetation and other debris that meet current ANSI Z87.1 standards and...to others, also loan them to instruct other than the speed needed to do a better, safer job when used at the ... unit immediately. Secure hair above shoulder level.
• The cutting head shield must be in the starting . Inspect the unit for an ...
Operation Manual - Page 4
...fuel containing
greater than 10% ethanol will likely damage this engine and void the warranty.
Use a full face shield when needed.
• UNLEADED FUEL Always use clean, fresh unleaded fuel.
• OIL Refer to the operator and/or bystanders... pets, at high
speed, causing injury. When turned off they remain hot for complete safety, assembly, operating and maintenance and repair information.
Operation Manual - Page 5
...
On/Off Switch
Muffler
Spark Plug
Starter Rope Grip
Primer Bulb
Fuel Cap
Handle Shaft Housing
Air Filter Cover
Throttle Control
Choke Lever
Cutting Head
Coupler
Cutting Head Shield
Oil Fill Plug
Line Cutting Blade
SPECIFICATIONS*
Engine Type Air-Cooled, 4-Cycle Displacement 30 cc (1.83 cu. in.) Spark Plug Gap 0.025 in...
Operation Manual - Page 6
...2).
6.
Loosen the bolt with a 3/8" socket, but do not tighten the bolt completely.
3. ASSEMBLY
INSTALLING THE CUTTING HEAD SHIELD
WARNING: To prevent serious personal injury, never
operate the unit without a hole) ...on the mount bracket into the slot on the cutting head shield with this unit.
1. Remove the wing nut and washer from the end of the shaft grip (Fig. 3)....
Operation Manual - Page 7
... the upper and lower shafts prior to the unit, shut the unit off before removing or installing an attachment.
Turn the knob counterclockwise to tighten (Fig. 4). NOTE:... that came with the guide recess will help installation (Fig. 5). 3.
For decorative edging with a string trimmer attachment, lock the release button into the primary hole (Fig. 6). While firmly holding the attachment...
Operation Manual - Page 8
OIL AND FUEL
USING THE RIGHT OIL
Use a high-quality SAE 30 weight oil. NOTE: This unit comes with gasoline. 6. Remove the cap from the oil bottle. DO NOT
overfill.
Use the bottle to measure the
correct amount of oil. 1. The importance of...Change the oil according to use clean oil of maintaining the proper oil level cannot be added before each use dirty oil. Remove the paper seal.
Operation Manual - Page 9
...fuel containing greater than 30 days old). Do not start the engine until fuel vapors dissipate.
1. Remove the fuel cap. 3. Reinstall the fuel cap. 6. NOTE: Dispose of old fuel according to ... is the most common cause of performance problems. Use only fresh, clean unleaded gasoline. WARNING: Remove the fuel cap slowly to the unit's fuel tank. Avoid creating a source of gasoline and...
Operation Manual - Page 10
... to Checking the Oil Level.
2. NOTE: SQUEEZE and HOLD the throttle control for 2-5 minutes, or as needed . Squeeze the throttle control (Fig. 9) and pull the starter rope with a controlled and steady motion 3... 12
10 Fill the fuel tank. The On/Off switch is no need to Position 2 (Fig. 11).
8. Continue to a complete stop (Fig. 9). Pull the starter rope with step 3. Continue to ...
Operation Manual - Page 11
... seconds.
8. Run the electric start accessory in intervals no need to Position 1 (Fig. 11).
5. Run the electric start accessory for ALL further steps.
7. Remove the electric start port (Fig. 13). Allow the engine.... Then move the choke lever to Position 2, and run the unit for 30 to a complete stop (Fig. 9).
11 The unit may be used during this instruction.
Check the oil level...
Operation Manual - Page 12
...running. TIPS FOR BEST TRIMMING RESULTS • Keep the cutting head parallel to the ground. • Cut from the cutting head without the need for bending over. Keep the left arm straight. • Hold... extended. CAUTION: Do not remove or alter the line cutting blade
assembly. Trimming line can be released from left hand.
NOTE: Do not rest the cutting head on the ground while the ...
Operation Manual - Page 13
... the oil. If necessary, remove any seasonal tune-up. Pull the line until the ends are unsure about 5 inches (12.7 cm) protrude from the cutting head.
Refer to the unit. ... MAINTENANCE
WARNING: To prevent serious injury, never perform
maintenance or repairs while the unit is complete. Disconnect the spark plug wire to align the arrows (Fig. 17). 4. MAINTENANCE SCHEDULE
...
Operation Manual - Page 14
... on the spool cover with the holes on the cutting head (Fig. 19). 2. The importance of maintaining the proper oil level cannot be overemphasized. Look into the holes. Unscrew the oil fill plug. 3. Inspecting the Oil Level Window 1. NOTE: Failure to overfill. 3. Remove any oil that the engine is approximately
halfway up...
Operation Manual - Page 15
...and allow it to prevent debris
from the air filter housing (Fig. 24). 3. Unscrew the cover screw completely. Lightly coat the air filter with clean SAE 30 oil. 5. Insert the tab on the air filter cover...OIL
Change the oil while the engine is in place on the oil fill plug (Fig. 21). Remove the air filter from entering the oil fill hole. 2. Rinse the air filter
thoroughly and allow ...
Operation Manual - Page 16
...engine will not idle, adjust the idle speed screw as needed ) until snug. Checking the fuel, cleaning the air filter...engine power
MAINTAINING THE SPARK PLUG
1. Reattach the spark plug boot. Remove the spark plug from the spark plug.
2. Tighten the spark ... is cracked, fouled or dirty, replace it from the cylinder head with a 5/8-inch socket, turning it to prevent serious personal injury...
Operation Manual - Page 17
...ventilated area. • Store the unit out of the reach of the unit. Reinstall the fuel cap.
2. Remove the spark plug and put 5 drops of old fuel according to federal, state and local regulations.
17 Repair ... Change the oil.
If this is not possible, store the unit vertically with a soft cloth. Remove the fuel cap, tip the unit and drain the fuel into the cylinder. This ensures that has...
Operation Manual - Page 18
... engine is hot
TROUBLESHOOTING
SOLUTION
Fill the fuel tank with new line Rewind the line Clean the inner reel and outer spool Open the cutting head and remove the welded section Rewind the line Stop the unit, push the bump knob and pull the line until 4 inches (102 mm) is outside of...
Operation Manual - Page 20
... of merchantability or fitness for a particular purpose, applies after the applicable period of any Troy-Bilt Product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for rental expenses to temporarily replace a warranted product. (Some states do not allow limitations on how...
Similar Questions
Remove String Trimmer Head?
I've replaced string often. This time the plastic cap on the bolt came off and the bolt turns the sh...
I've replaced string often. This time the plastic cap on the bolt came off and the bolt turns the sh...
(Posted by eneguesicnarf 1 year ago)
Can You Replace The Bump Feed String Head With A Fixed Line Head?
(Posted by Ibbroman 8 years ago)
How To Remove Cutting Head
How To Remove Cutting Head From Tb525 Ec Trimmer
How To Remove Cutting Head From Tb525 Ec Trimmer
(Posted by godez 10 years ago)