TP-Link TD-8817 Support Question
Find answers below for this question about TP-Link TD-8817.Need a TP-Link TD-8817 manual? We have 2 online manuals for this item!
Question posted by giseato on May 1st, 2014
How I Can Do Automatic Connect Tp-link Td-8817
The person who posted this question about this TP-Link product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
There are currently no answers that have been posted for this question.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Related TP-Link TD-8817 Manual Pages
User Guide - Page 9
... LINE port is linked down
On
A successful PPP connection has been established
Internet
Flash Off
Data is being transferred over the Internet
There is failed
3 For details, please refer to LED Explanation. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Chapter 2. Hardware Installation
2.1 The Front Panel
Figure 2-1 The LEDs are located on Bridge mode
Power
On...
User Guide - Page 14
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Step 4: Configure the IP address as Figure 3-4 shows. Now, you can configure the PC to get an IP address automatically, select "Obtain an IP address
automatically" and "Obtain DNS server address automatically" in the screen above.
Please click the Start menu on the following appeared command prompt screen and...
User Guide - Page 15
... correct?
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide If the result displayed is 192.168.1.1, your PC's IP address must install the USB's driver to the computer. Step 2: Soon, Figure 3-7 will display after a moment.
Figure 3-6 You can obtain the drivers from the provided CD, or download from our website. (http://www.tp-link.com...
User Guide - Page 23
...These QoS types are four connection types: Dynamic IP Address, Static IP Address, PPPoA/PPPoE and Bridge Mode. Please input the value... . • VPI: Identifies the virtual path between endpoints in Bridge mode. ¾ NAT: Select this option to 255. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide setup each PVC traffic line's priority. • Virtual..., you an IP address automatically.
User Guide - Page 25
... in Bridge mode. ¾ Connection: For PPPoE/PPPoA connection, you can select Always on or Connect
on the traffic. Connect on demand is dependent on -Demand or Connect Manually. If there is traffic send or receive, the connection will tear down automatically. And once there is no traffic (or Idle) for your PPPoE connection. Please enter the information accordingly.
TD-8817...
User Guide - Page 28
...: The length of the IP address that assigns the
22 By default, the DHCP Server is 192.168.1.2, and the Start IP Address must be automatically assigned a new dynamic IP address. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide connected to the clients on the network.
User Guide - Page 31
...) function for this link. IP Routing uses hop count as your ADSL Router that approximates the cost for the Router (shown in Figure...kept private and is an immediate
neighbor of your Router; TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Figure 4-14 Click ADD ROUTE button... of transmission for directly connected networks.
Figure 4-15 ¾ Destination IP Address: This parameter specifies...
User Guide - Page 49
... the function, then the UPnP network devices can
automatically configure network addressing, announce their presence in Figure ...the screen (shown in the network to -peer network connectivity between network devices. UPnP broadcasts are only allowed on the...) is used for exchanging information between devices.
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Management Protocol (SNMP) is a ...
User Guide - Page 52
...take effect.
4.6.2 Time Zone
Choose "Maintenance→Time Zone", you can manually set the time or connect to a NTP (Network Time Protocol) server. There are three methods to configure the time. The default... 4-38 46 The system time is "admin". TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Figure 4-37
) Note:
1) There is set, you will automatically adjust on those dates. 1.
User Guide - Page 53
... Router will get the system time automatically from the specific Server firstly. 2.
You can upgrade the firmware of the computer. PC's Clock Select PC's Clock as the Synchronize time, you can also configure the NTP Server address manually, and then the Router will get the time from the NTP Server. TD-8817 ADSL2/2+ Ethernet/USB Router...
User Guide - Page 54
... 4-42) to proceed.
48 TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Figure 4-41 To upgrade the router's firmware, follow these instructions below...router or press the Reset button while the firmware is no need to download a more recent firmware upgrade file from the TP-LINK website
(www.tp-link.com). Step 3: Click the UPGRADE button.
) Note:
1) New firmware versions are posted at www.tp-link...
User Guide - Page 13
... command prompt screen and then press Enter.
Figure 3-5 7 TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Step 4: Configure the IP address as Figure 3-4 shows.
After that, click OK.
) Note:
Figure 3-4
You can run the Ping command in the command prompt to the screen below, the connection between your desktop, select run tab, type cmd...
User Guide - Page 14
...the provided CD, or download from our website. (http://www.tp-link.com)
USB Drive installation procedures
Step 1: Please connect your PC to the Router through the USB port at first, then open the relative ...
You can check it means that your PC has not connected to the Router.
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide If the result displayed is 192.168.1.1, your PC correct?
User Guide - Page 22
...the virtual path between endpoints in an ATM network. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide • Status: If you want ... please configure them according your ISP provides you an IP address automatically.
Please input the value provided by your ISP. •... and RIP2-M are four connection types: Dynamic IP Address, Static IP Address, PPPoA/PPPoE and Bridge Mode. The valid range is...
User Guide - Page 23
...TD-8817 ADSL2/2+ Ethernet/USB Router User Guide RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format. • Direction: Select this option to obtain an IP address automatically for your PPPoE connection...PPPoE to specify the RIP direction. IN only means the ADLS router will only accept but will periodically send routing information and accept routing...
User Guide - Page 24
... PVC as the default gateway to specify the public IP address for this device. 4. The IP address can select Always on or Connect
on-Demand or Connect Manually. Bridge Mode
18 If there is dependent on the traffic. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Figure 4-7 ¾ Username: Enter your username for your PPPoE/PPPoA...
User Guide - Page 27
...(shown in Figure 4-11), the
Router will work as a DHCP Relay. Figure 4-11 • DHCP Server IP for you to use DNS relay, you can be automatically assigned a new dynamic IP address....PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the connection establishment. If you want to 192.168.1.1 on WAN side. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide expired, the user will be configured as no...
User Guide - Page 29
...connected networks. IP Routing uses hop count as your ADSL Router that approximates the cost for this route is kept private and is usually a good number. ¾ Announced in Figure 4-16).
23 If No, this link...Network Address Translation) function for this remote node in Figure 4-15). TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Figure 4-14 Click ADD ROUTE button to other hosts ...
User Guide - Page 47
... enable exchange of simple product and service descriptions.
41 TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
4.5.3 SNMP
Choose "Access Management→SNMP", you activate the function, then the UPnP network devices can
automatically configure network addressing, announce their presence in the network to -peer network connectivity between network devices. UPnP broadcasts are only allowed...
User Guide - Page 52
... are posted at www.tp-link.com and can be used for free. To back up the router's current settings before you upgrade its firmware.
3) Do not turn off the router or press the Reset ...name of the update file into the "New Firmware Location" field. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Figure 4-41 To upgrade the router's firmware, follow these instructions below: Step 1: Download a more ...