Singer 4411 Heavy Duty Support Question
Singer 4411 Heavy Duty Support Question
Find answers below for this question about Singer 4411 Heavy Duty.Need a Singer 4411 Heavy Duty manual? We have 1 online manual for this item!
Question posted by Justwhatilikeaccessories on June 17th, 2014
The Stitch Is Clumping Up And Popping The Bobbin Is Making A Noise
The machine starts to sew and right after the thread pop,sound like the bobbin is making a clapping sound
Current Answers
Related Singer 4411 Heavy Duty Manual Pages
Instruction Manual - Page 2
... threading needle, changing needle, threading bobbin, or changing presser foot, and the like. 10. Special care is being used by or near children. 2. Always use by persons (including children) with any object into water. If the supply cord that they have been given supervision or instruction concerning use of electric shock:
1. Switch the sewing machine...
Instruction Manual - Page 6
... Machine Winding the Bobbin ...12 Inserting the Bobbin ...14 Threading the Upper Thread ...16 Raising the Bobbin Thread ...18 Thread Tension...20
Sewing How to Choose Your Pattern ...22 Three Needle Position Dial...24 Stitch Width Dial & Stitch Length Dial ...26 Sewing Straight Stitch ...28 Reverse Sewing/ Removing the Work/ Cutting the Thread 30 Blind Hem ...32 Buttonholes ...34 Left and Right...
Instruction Manual - Page 9
Bobbin stopper
5
11. Pattern selector dial 7
8
2 Thread cutter
1
9
6. Removable extension table/ accessory storage
4
12
9. Thread tension dial
2. Stitch length dial
6
13. Reverse sewing lever
5. Needle plate cover
3
8. Three needle position dial
10. EN Principal Parts of the Machine
1. Presser foot pressure adjustment
3. Thread take-up lever
4. Stitch ...
Instruction Manual - Page 11
...thread guide
23. Drop feed control
27. Bobbin thread guide
22. Horizontal spool pin
15. Hole for auxiliary spool pin 15
17. Buttonhole stitch... balance adjustment slot
16
19. Power and light switch 17
20. Handle
19
25. Handwheel
18. Power cord
4
21 22 23 24 25
27 28
26 Presser foot lifter 20
26. Foot speed control 28. EN Principal Parts of the Machine
14. Bobbin...
Instruction Manual - Page 13
...
b. Do not modify the plug in the outlet, reverse the plug. Foot control The foot control pedal regulates the sewing speed. (3)
Attention: Consult a qualified electrician if in use . Unplug power cord when machine is not in doubt of electric shock, this plug is wider than the other). To reduce the risk of...
Instruction Manual - Page 15
... can be raised to a higher position for heavy fabric, tighten by turning it clockwise.
8 For sewing very thin fabric, loosen the pressure by turning the screw counter clockwise, and for easy positioning of the work. (A)
A
Adjusting Presser Foot Pressure
The presser foot pressure of the machine has been pre-set and requires no...
Instruction Manual - Page 17
...authorized retailer.)
n. Satin stitch foot o. Hemmer foot q. Darning/ embroidery foot v. Zipper foot c. Buttonhole foot d. L-screwdriver k. Seam ripper/ brush f. Bobbin (3x) j. Overcasting... foot b. Edge/ quilting guide g. Button sewing foot e. Pack of needles h. Spool pin felt m. they are not supplied with this machine; Cording foot r. Quilting/ straight stitch foot t.
Instruction Manual - Page 19
...Note:
When the bobbin winder spindle is in "bobbin winding"
position, the machine will not sew and the handwheel turn. EN Winding the Bobbin
- Thread bobbin as illustrated and place on foot control pedal. (8)
- To start sewing, push the bobbin winder spindle to left
(sewing position).
4
3
5
6
7
8
9
10
12 Hold thread end. (7) 1
- Wind thread clockwise around bobbin winder tension...
Instruction Manual - Page 25
Note: If it is difficult to raise the bobbin thread, check to make sure the thread is not trapped by the hinged cover or the Removable Extension Table.
1 Gently pull on the upper thread to bring the bobbin thread up through the needle plate hole. (2) Lay both threads to the back under the presser foot. (3)
2
3
18 Turn the handwheel...
Instruction Manual - Page 27
... next number up. Proper tension setting is when a small amount of the upper thread appears on the bottom side of fabric. C
D
20 B. For zig zag and decorative sewing stitch functions, thread
tension should generally be between "3" and "5". A.
Lower thread tension
The bobbin tension has been set correctly at the factory, so you will be less than...
Instruction Manual - Page 29
... Your Pattern
The diagram on this page display the stitch patterns available on the machine. The Pattern Selector Dial may be turned in either direction. Reverse Sewing Lever b. Stitch Length Dial e. Pattern Selector Dial
ABCDE FGH I J
3
4
2
1
22 EN How to adjust the width of the stitch as desired for the project. Three Needle Position Dial...
Instruction Manual - Page 31
..., the needle position is middle. EN Three Needle Position Dial
The needle position can be altered with the "Three needle position dial". For twin needle stitching, needle position is middle.
Left Needle Position M. Middle Needle Position R. Straight b. a. Zig-zag L. For edge stitching or sewing parallel lines of top stitch, select needle position left or right.
Instruction Manual - Page 33
... finer needle or thread.
2
26
4 3 2 1 0.5 Use a shorter stitch length when sewing lighter weight fabrics or when using a thicker needle or thread.
The length of the individual stitches will decrease as the setting of stitch length dial for zigzag stitching is 5mm; EN Stitch Width Dial & Stitch Length Dial
Function of stitch length dial while zig-zag stitching
Set the Pattern Selector...
Instruction Manual - Page 35
EN Sewing Straight Stitch
To begin sewing, set the machine for straight stitch. (1) Place the fabric under the presser foot with the fabric edge lined up with the desired seam guide line on the needle plate. (2) Lower the presser foot lifter, and then step on the foot controller to start sewing. (3)
1
2
3
28
Instruction Manual - Page 37
A
Release the lever and the machine will sew forward again. (1)
Removing the Work
Turn the handwheel toward you (counterclockwise) to bring
the thread take up lever to the side of a seam, press down to cut. (3)
30
B 3 Pull threads down
the reverse sewing lever (A).
Guide the threads to its highest position, raise the
presser foot and remove work...
Instruction Manual - Page 39
... the Stitch Width Dial at the right. EN Blind Hem
For hems on the fold, making sure the needle touches slightly the folded top to the desired width and press. Sew a test first to the
right side of the
page. Fold back
(as shown in the diagram on the right of the folded fabric.
1
Start to sew slowly...
Instruction Manual - Page 41
... may need to another with starting marking on the fabric you are using to set stitch density. Slightly reducing upper thread tension will produce better
results.... stitch width at "6". Always test sew a buttonhole on fabric. Tips: - Measure diameter and thickness of the buttonhole foot (b). Adjust the Stitch Length Dial in steps 1 and 3.
The zig-zag should sew over the heavy thread ...
Instruction Manual - Page 45
... right holes of the button. "6". Slowly sew on the button with 4 holes, sew through the front two holes first, push the work forward and then sew through the back two holes.
3
4
38 For buttons with about 10 stitches.
Set the machine for zig-zag stitch, then set the width to "0". Set the machine for straight
a
2
ba b
stitch again, then sew...
Instruction Manual - Page 51
... tricot, single and double knits. For best sewing results always use the same thread on natural woven fabrics for best
Heavyweight fabrics-canvas...Heavy woolen, overcoat fabrics, upholstery fabrics, some Heavy duty thread, carpet thread.
Natural and synthetic woven fabrics, polyester blends. EN Needle/ Fabric/ Thread Chart
NEEDLE, FABRIC, THREAD...thread breakage or skipped stitches.
44
Instruction Manual - Page 60
... suit the fabric and thread. 4. Remove bobbin case, thread and insert correctly. 3. The needle is too tight. The machine is threaded wrong. 3. Clean the hook and feed dog as illustrated. 3. The bobbin case is noisy
The machine jams
1. The needle is too tight. 3. Select a finer needle. 2. Do not pull on the fabric while sewing, let the feed dogs...
Similar Questions
Machine Start Up
my quantum will not run the start up when turned on. It beeps but the needle doesn't adjust. I am un...
my quantum will not run the start up when turned on. It beeps but the needle doesn't adjust. I am un...
(Posted by Dgmcmaster 1 year ago)
The Problem Is Specific To Reverse Stitching, It Is Not A General Machine
question regarding normal operations.
question regarding normal operations.
(Posted by dwdsad 7 years ago)
Thread Underneath Fabric In Large Loops.
When sewing the thread under the fabric comes in large loops. The tension wheel of the upper thread ...
When sewing the thread under the fabric comes in large loops. The tension wheel of the upper thread ...
(Posted by hanserikjohansson 7 years ago)
Hand Wheel Won't Turn And Makes A Loud Clicking Noise.
I just received my new singer h74 today and afete setting it up I was testing different tensions. Al...
I just received my new singer h74 today and afete setting it up I was testing different tensions. Al...
(Posted by Lbrobinson83 10 years ago)
Singer 7469q Confidence Quilter - Beeping Noise And Machine Freezing
I was in the midst of using one of the novelty stitches and all of a sudden the machine locked up, b...
I was in the midst of using one of the novelty stitches and all of a sudden the machine locked up, b...
(Posted by whitewavejl 10 years ago)