Ridgid R3250 Support Question
Ridgid R3250 Support Question
Find answers below for this question about Ridgid R3250.Need a Ridgid R3250 manual? We have 1 online manual for this item!
Question posted by jmmorales761 on May 5th, 2014
Need Screws For Auxiliary Handle Thnx 3250 Twin Blade.
The person who posted this question about this Ridgid product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Ridgid R3250 Manual Pages
Owners Manual - Page 3
.... WORK AREA SAFETY
Keep work area clean and well lit. ELECTRICAL SAFETY
Power tool plugs must be repaired.
Disconnect the plug from the power source and/or the battery pack... your body is unavoidable, use common sense when operating a power tool. POWER TOOL USE AND CARE
Do not force the power tool. If damaged, have the switch on invites accidents.
...
Owners Manual - Page 4
...auxiliary handle, or motor housing. Kickback may contact hidden wiring or its own cord. When the blade is binding, or when interrupting a cut and reduces the chance of blade binding.
Always use blades with only one blade...cause kickback.
Check lower guard for optimum performance and safety of the power tool "live " wire will also make sure it may occur. If saw if lower ...
Owners Manual - Page 5
...be released. Following this rule will cause a drop in line voltage resulting in loss of the tool, a guard or other part that the lower guard is in a well ventilated area, and...as needed, when using an extension cord, be properly repaired or replaced by retracting handle and as soon as the specific potential hazards related to walk backwards, cutting whatever is covering the blade ...
Owners Manual - Page 6
... load
.../min
Per Minute
Revolutions, strokes, surface speed, orbits etc., per minute
Wet Conditions Alert
Do not expose to keep your hands away from the blade will result in death or serious injury.
Owners Manual - Page 7
...tools, which eliminates the need to your tool does not operate when plugged into an outlet, doublecheck the power supply.
When working area. If damaged replace immediately.
Never use . Observe all normal safety precautions to handle the current the tool..., be used. Use the chart to do not need for outside use tool with a damaged cord since touching the damaged area ...
Owners Manual - Page 8
...Blade Outer Blade Auxiliary Handle Screws (3) Flat Washers (2) Lock Washers (2) Wax Sticks Heavy-Duty Contractor Bag Blade Wrench Operator's Manual
WARNING:
If any parts are attempting.
English FEATURES
PRODUCT SPECIFICATIONS Blade...or removing blade. WARNING:
This twin blade saw blade teeth don...tool and in this operator's manual as well as a knowledge of this product. Use of blades...
Owners Manual - Page 9
... 4.
Using Phililips screwdriver, secure the bottom of the auxiliary handle. Tighten screw securely.
9 - English WARNING:
Always use both blades. TO INSTALL THE AUXILIARY HANDLE
See Figure 4, page 15.
Slide the top of the auxiliary handle into the hole in the front handle.
Place the bottom of the auxiliary handle into the slot as shown in the top of...
Owners Manual - Page 10
...towards you have the guard repaired or replaced. Never
force a cut . BLADE GUARD SYSTEM
The lower blade guard attached to the twinblade saw is sufficient to avoid kickback and possible ... and fingers away from the workpiece while the blades are moving blade will not cut . Operating the tool incorrectly or misusing the tool. Always leave guard in horizontal cuts, make ...
Owners Manual - Page 11
... that is always to "kickback" towards you drop the saw, check the lower blade guard and bumper for damage before using the saw into the workpiece. Leaving the blade exposed could result in a raised position. Check the guard for handling the saw from the cutting area. The guard is important to its normal...
Owners Manual - Page 12
... copper, stainless steel, etc.).
Remove the cap on the front handle as shown.
Start the saw and let the blade reach full speed.
Guide the saw , turn wax dial counter-... cut .
MAINTENANCE
WARNING:
When servicing use . GENERAL MAINTENANCE
Avoid using the lower blade
guard handle. Most plastics are lubricated with ANSI Z87.1.
WARNING:
Always wear eye protection with...
Owners Manual - Page 13
...Warranties for RIDGID® branded hand held and stationary power tools. You may not apply to , blades, bits and sand paper are not covered. This warranty ... particular purpose, that cannot be directed to One World Technologies, Inc., attn: RIDGID Hand Held and Stationary Power Tool Technical Service at (toll free) 1-866-539-1710.
90-DAY SATISFACTION GUARANTEE POLICY
During the first 90 days ...
Owners Manual - Page 37
...blade guard lip (lèvre de garde de
E - Incorrect support (support incorrect, soporte incorrecto)
Fig. 6
Fig. 9
WRONG / INCORRECT / FORMA INCORRECTA
A - Auxilary handle (poignée auxiliaire, mango A - Switch trigger (gâchette de commutateur,
auxiliar)
gatillo del interruptor.)
D - Front handle...A
CAVIDAD
B C
F AD G
B
A - Screw (short) [vis (court), tornillo (corto)
Fig. ...
Similar Questions
Ridgid Ms255sr 'inner Screw'
I have the Ridgid ms255sr and can't find the "inner screw" (fig 10) http://www.homedepot.com/catalog...
I have the Ridgid ms255sr and can't find the "inner screw" (fig 10) http://www.homedepot.com/catalog...
(Posted by doug29112 8 years ago)
How To Adjuest Air Press On Ridgid R350che
I can't fine in the operators manual for my r350che that part that tells me how to adj. the pres. On...
I can't fine in the operators manual for my r350che that part that tells me how to adj. the pres. On...
(Posted by Rivergod177 9 years ago)
Metal Cutting Bandsaw Blade
Just bought a used RIDGID BS14000 bandsaw, has a wood blade on it, but I want to cut metal. Need to ...
Just bought a used RIDGID BS14000 bandsaw, has a wood blade on it, but I want to cut metal. Need to ...
(Posted by DavidYork 10 years ago)
How Do I Change Blades?
I want to change blades on my saw and I can't find my manual.
I want to change blades on my saw and I can't find my manual.
(Posted by gtb53 11 years ago)