Ridgid R3250 Support Question

Find answers below for this question about Ridgid R3250.
Need a Ridgid R3250 manual? We have 1 online manual for this item!

Ridgid Overview Questions Manuals Reviews Videos Research

Question posted by gibberfest on February 21st, 2024

Ridgid R3250

Where are you supposed to get new blades?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on February 22nd, 2024 7:06 AM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,596,890

1,100
points

https://www.toolpartspro.com/ridgid-parts/ridgid-r3250-parts/ridgid-039438001106-blade-assembly

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Ridgid R3250 Manual Pages

Owners Manual - Page 3

...not wear loose clothing or jewellery. Read all times. ELECTRICAL SAFETY  Power tool plugs must be controlled with earthed or grounded surfaces such as dust mask, non-skid... used . Do not use a ground fault circuit interrupter (GFCI) protected supply. GENERAL POWER TOOL SAFETY WARNINGS AND INSTRUCTIONS WARNING! Failure to lose control. WORK AREA SAFETY  Keep work...

Owners Manual - Page 4

... that the safety of operation. Keep your saw to lift up or kickback from cutting area and the blade. It is binding, or when interrupting a cut for optimum performance and safety of the power tool is accidentally dropped, lower guard may be avoided by insulated gripping surfaces when performing an operation where...

Owners Manual - Page 5

...Wear non-slip, heavy-duty protective gloves, as blade enters the material, the lower guard must be ...tool, a guard or other sawing, the lower guard should be released. Following this product.  Always wear eye protection with ANSI Z87.1. A guard or other reproductive harm. A wire gauge size (A.W.G.) of the lower guard spring. A cord exceeding 100 feet is recommended for the blade...

Owners Manual - Page 6

... To reduce the risk of these symbols will result in death or serious injury. No Hands Symbol Failure to keep your hands away from the blade will result in damp locations. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury. English SYMBOL SIGNAL MEANING...

Owners Manual - Page 7

...wire size required in an extension cord. NOTE: Servicing of power. ELECTRICAL CONNECTION This tool has a precision-built electric motor. Never use an extension cord that it for outside... wiring. Failure to do not need for repair. It should be connected to use tool with protecting insulation. When working area. WARNING: Check extension cords before each use original...

Owners Manual - Page 8

...assembly is not completely assembled or if any parts are included. WARNING: This twin blade saw blade teeth don't "dry cut 1-1/32 in the packing list are damaged or missing,... FEATURES PRODUCT SPECIFICATIONS Blade Diameter 5 in . Outer Blade Arbor 3/4 in . PACKING LIST 5 in . Use of this operator's manual as well as a knowledge of the information on the tool and in this product...

Owners Manual - Page 9

... the saw.  Check to move freely.  Remove the outer blade then remove the inner blade. English Make sure the lower guard spring works properly, allowing the guard to see... lock, always allow motor to come to loosen.  Retract the lower guard into the upper blade guard using two short screws, lock washers, and flat washers.  Place the long screw into...

Owners Manual - Page 10

... reason. To guard against kickback, avoid dangerous practices such as:  Twisting the blades while making a cut. This helps prevent twisting the blades.  Use clean and sharp blades. Never force a cut .  Operating the tool incorrectly or misusing the tool. Always leave guard in objects being thrown into your body in the workpiece. English...

Owners Manual - Page 11

...could lead to learn the correct and incorrect ways for handling the saw , check the lower blade guard and bumper for operating the saw into the workpiece. WARNING: If the cord hangs up... guard, do not use . WARNING: Using a saw . If you release the switch trigger, allow the blade to come to understand the correct method for damage before setting the saw : Depress the switch trigger. Take...

Owners Manual - Page 12

... saw, the user may create a hazard or cause product damage. GENERAL MAINTENANCE Avoid using the lower blade guard handle. Chemicals can damage, weaken or destroy plastic which may be done by an authorized service ...comply with the lever.  Hold the lower blade guard by their use only identical RIDGID® replacement parts. POWER SUPPLY CORD REPLACEMENT If replacement of cut .

Owners Manual - Page 13

...in to , blades, bits and sand paper are not covered. This warranty only covers defects arising under state law are disclaimed. Consumable accessories provided with the tool such as brushes..., all defects in this RIDGID® tool for this RIDGID® Hand Held and Stationary Power Tool for RIDGID® branded hand held and stationary power tools. ADDITIONAL LIMITATIONS To the ...

Owners Manual - Page 37

... stick (bâton de cire, palillo de cera) B -Wax dial (cadran de cire, dial de cera) Fig. 12 CUTTING PIPE / COUPE TUYAU / CORTE TUBOS A - Lower blade guard lip (lèvre de garde de E - Flat washer (rondelle plate, arandela plana) B - Auxilary handle (poignée auxiliaire, mango A - Lock washer (rondelle frein, arandela de...