Lexmark E360DN Support Question
Lexmark E360DN Support Question
Find answers below for this question about Lexmark E360DN - Hv Taa/gov Compliant.Need a Lexmark E360DN manual? We have 6 online manuals for this item!
Question posted by cjsecjdust on June 13th, 2014
New Fuser Lexmark C543dn How To Reset Factory
The person who posted this question about this Lexmark product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Lexmark E360DN Manual Pages
Troubleshooting Guide - Page 6
... TYPE SETTING
Make sure the Paper Type setting matches the paper loaded in the tray.
Try one or more of the printer might be caught between the photoconductor kit and the fuser. CAUTION-HOT SURFACE: The inside of the following :
6
THE TONER MAY SMEAR WHEN PAPER IS FED FROM A
SPECIFIC SOURCE From...
Troubleshooting Guide - Page 7
... BE DEFECTIVE OR LOW ON
TONER Replace the used toner cartridge with a new one or more information, see your printer. Try one or more information, see . CHECK THE NETWORK SETTINGS
Depending ...Make sure the Paper Texture setting is correct for the type
of the printer might be caught between the photoconductor kit and the fuser.
MAKE SURE THE PAPER PATH IS CLEAR
Paper could be hot.
For...
User's Guide - Page 1
... rights reserved. 740 West New Circle Road Lexington, Kentucky 40550 All other countries. Lexmark E360d and E360dn Series
User's Guide
May 2008
www.lexmark.com
Lexmark and Lexmark with diamond design are the property of Lexmark International, Inc., registered in the United States and/or other trademarks are trademarks of their respective owners.
© 2008 Lexmark International, Inc.
User's Guide - Page 5
......100
Replacing the toner cartridge ...100 Replacing the photoconductor kit ...101
Recycling Lexmark products...104 Moving the printer...104
Before moving the printer ...104 Moving the printer to another location...104 Setting the printer up in a new location ...105 Shipping the printer ...105
Administrative support 106
Finding advanced networking and administrator information 106 Adjusting...
User's Guide - Page 7
...printer might be obvious.
Lexmark is misused, a risk of the printer...printer before removing paper from the wall outlet before proceeding. CAUTION-HOT SURFACE: The inside of specific Lexmark...printer, then turn the printer ... going into the printer. CAUTION-SHOCK HAZARD...printer near the product and easily ...printer,...printer. If you are installing an optional drawer after setting up the printer...
User's Guide - Page 78
... Trace, turn the printer off or reset the printer. Flash memory refers to the memory added by retrieving lost storage space Warning-Potential Damage: Do not turn off the printer while the flash memory...new data by installing an optional flash memory card in isolating the source of printed objects Note: 0 is the factory default setting.
Warning-Potential Damage: Do not turn off the printer...
User's Guide - Page 124
...Check the paper path around the fuser area. THERE MAY BE EXCESS TONER IN THE PAPER PATH
Contact Customer Support.
To reduce the risk of the printer might be hot.
Streaked vertical ... component, allow the surface to feed paper for the job. To reduce the risk of the printer might be hot.
Clear any paper you are possible solutions. Warning-Potential Damage: Do not touch...
User's Guide - Page 137
..., AND ABSENCE OF VIRUSES, ALL WITH REGARD TO THE SOFTWARE PROGRAM.
IN NO EVENT WILL LEXMARK, ITS SUPPLIERS, SUBSIDIARIES, OR RESELLERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, EXEMPLARY, ... the extent Lexmark is ninety (90) days and commences on Lexmark that Lexmark is delivered to state. This limited warranty applies only to Software Program media purchased new from state ...
Service Manual - Page 4
...menus 3-2 Reset photoconductor maintenance counter (Reset PC Cnt 3-3 Print quality pages (Prt Quality Pgs 3-3 Reports 3-3 Panel Menus 3-3 PPDS Emulation 3-3 Demo Mode 3-4 Factory Defaults ...gear drive interface removal 4-13 Fan removal 4-16 Front access door removal 4-17 Fuser removal 4-20 Left print cartridge guide removal 4-23 Left side cover removal 4-24...Lexmark™ E360d, E360dn
Service Manual - Page 27
... Voltage Power Supply Liquid Crystal Diode Light Emitting Diode Laser Scanning Unit Low Voltage Power Supply Nonvolatile Random Access Memory Photoconductor Printer Control Language Power-On Reset Power-On Self Test Personal Printer Data Stream People's Republic of China Toner Add Roll Synchronous Dynamic RAM Shipped With Equipment Universal Serial Bus Volts alternating...
Service Manual - Page 35
Replace the maintenance items and, if necessary, reset the printer maintenance counter. The printer menus are simplexed. Contact a system support person. Press to make the printer ready to take the printer offline.
The printer is programming new engine code.
The printer is processing or printing the menu settings page.
4513-420, -430
User attendance messages (Continued)
...
Service Manual - Page 36
... 600 dots per inch (dpi) to 300 dpi to print the contents of the buffer. • Cancel the current job.
2-8 Lexmark™ E360d, E360dn
Res Reduced remains on the fuser.
The printer is resetting the counter that tracks wear on the display while the job prints.
Wait for an End of Job command, a Form Feed...
Service Manual - Page 44
...fuser installed in the printer.
This applies to the fuser and belt fusers...Belt fuser ...fuser was under temperature when the media reached the fuser nip.
923.00 Fuser is over temperature.
923.01
Fuser...new enhanced control).
922.07 Media reached fuser nip, and fuser is under temperature
922.08 Fuser warm-up failure (motor start condition)
922.09 Fuser...fuser and belt fusers.
925.xx
Wrong fuser...
Service Manual - Page 46
...range of ECC bit corrections
2-18 Lexmark™ E360d, E360dn See "Operator panel service check" ...the controller board
Replace the controller board.
Install a new controller bored or operator panel. See "Controller board ... RIP card failure: ASIC failure
958.xx
Printer has performed more than 100 "shift and ... zero cross detected on belt fuser model
Replace the main motor gear drive.
...
Service Manual - Page 50
... is new, it obtains some of the controller board.
Cables are not correct on the controller board, then replace the controller board.
(Check with the printer positioned on . 4. Turn the printer off before plugging or unplugging any connectors.
2-22 Lexmark™ E360d, E360dn Turn the printer off . 2.
Power to display lights or activate the drive motor, fuser...
Service Manual - Page 60
... 2-25 for signs of image
FRU Fuser
Media (not a FRU)
Action
The fuser may require higher heat to properly fuse. Make sure recommended media is low, then try a new one. Check to prevent damage from finger oils or hand lotion. Variation in the printer driver.
2-32 Lexmark™ E360d, E360dn
4513-420, -430
Partial blank image...
Service Manual - Page 72
... features and options of the printer.
3-2 Lexmark™ E360d, E360dn Turn on page 3-3. Available menus
The menus display on the operator panel in the order shown:
Configuration menu settings
Reset PC Cnt
Prt Quality Pgs Reports
• Menu Settings Page • Event Log Panel Menus PPDS Emulation Demo Mode Factory Default Energy Conserve Font Sharpening...
Service Manual - Page 82
...PRINTER SETUP.
3-12 Lexmark™ E360d, E360dn After all print tests have been completed, the value will equal the values of a setting is changed . Note: The Permanent Page Count's value cannot be changed manually. Press to exit the Page Count setting and return to the Printer Setup menu.
factory...setting cannot be reset. 4513-420, -430
Printer setup
Printer Setup displays the...
Service Manual - Page 84
...Factory Defaults setting in the event log as well as the PC kit and maintenance counter resets and NVRAM resets initiated by one error per minute), but can be used when printing with a specific operating point. When deactivated, the printer...print contrast can be adjusted to exit the EVENT LOG.
3-14 Lexmark™ E360d, E360dn Charge Roll
The charge roll can be adjusted to 255.
No ...
Service Manual - Page 94
... obtains its settings from the USB port. A
4-6 Lexmark™ E360d, E360dn Critical factory settings are lost when both cards are new and are replaced at the same time. 4513-420, -430
Controller board removal
CAUTION This product contains a lithium battery.
Each card contains the printer
settings. Remove the three screws (A) from the other card. See...
Similar Questions
How To Reset Lexmark Printer E360dn
(Posted by shajes 9 years ago)
How To Set A New Top Of Form On A Lexmark 2500 Series Printer
(Posted by taeenrosa66 9 years ago)
How To Reset The Lexmark Printer E360dn
(Posted by littlNumbe 9 years ago)
How To Reset Memory For Lexmark Impact S305 Printer
(Posted by slikcold 9 years ago)
How To Reset Toner Low Message On An Lexmark E360dn
(Posted by crsoygan 10 years ago)