Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by waynelfrank on May 3rd, 2013
How To Reset Washing Machine
Washing machine model 110.92195510; serial # CB1401610. Machine became unbalanced and will not run. Lights on machine panel work (unit has electricity). Can I reset the motor by unplugging the washing machine, then plugging it in and pressing a combination of panel buttons?
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 8
... (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White with ...lbs.
1-4 SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft. IEC) Temperature Control
Heater Sensors
Tumble Speed
Spin Speed
Motor Voltage Frequency Amps Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds
Height Install ...
User Guide - Page 14
... Use two or more people to move it to the center of the unit is seated on the valve.
These bolts also retain the power cord inside the washer until the bolts are 4 bolts in the rear panel of the washer that the rear of the hole and completely pull out the bolt, including...
User Guide - Page 16
...Confirm the levelness of the washing machine top plate, the machine should be tightened.
Drape the power cord over the washer top.
2. Push on the upper front panel to its final location. 6. If the washer is level, use a ... hose on the top edge of the drain hose in the laundry tub or standpipe. Lower the right front foot until washer is perfectly level (use a 17 mm open-end wrench to...
User Guide - Page 19
.... ADAPTIVE VARIABLE SPEED MOTOR
The motor adapts to the load size and to the cycle selected to reach high-speed spins.
When this option is available at the beginning of water is no agitator, you can obtain the same results with traditional top load machines. This washer allows a 7-minute period in all wash cycles except Rinse/Spin...
User Guide - Page 20
... the optimal time for cleaning. SMART DISPENSERS
The three compartments in the dispenser allow loading of the cycle, and the bleach is started. The additives will be dispensed into the wash at the beginning of all laundry additives before the washer is
added after the enzymes have had a chance to do their cleaning. Use...
User Guide - Page 22
... run it...washer. The indicator light for the selected cycle will illuminate. The preset settings provide the recommended fabric care for a medium-sized load. USING THE PROPER DETERGENT
Use only High Efficiency detergents. This wash...Wash Cycles
1. To load washer
Open the washer door by pulling on the washer by selecting POWER. Sort laundry according to use. Place a load...
User Guide - Page 23
...wash cycle will likely result in hours) is complete, the CYCLE COMPLETE status light illuminates, the door unlocks, and the wash load can be marked "HE" or "High Efficiency." The washer powers down the washer...regular detergent will show in the dispensers when the wash cycle is complete, select PAUSE/CANCEL once.
8.
Add the desired laundry additives to avoid a spill). A C
MAX
...
User Guide - Page 24
...to restart the washer at the beginning of the new cycle.
To change Options after the wash cycle. Select DRAIN...machine will be automatically diluted and dispensed at any form of colorsafe bleach to this compartment. This compartment cannot dilute powdered bleach.
• Use only liquid chlorine bleach in Dispenser Illustration)
Add 1/4 cup (60 mL) liquid fabric softener to your load...
User Guide - Page 25
... pressure, water temperature, detergent, and clothes load.
The Estimated Time Remaining can change settings after the cycle has started , if the ADD A GARMENT status light is unbalanced.
Door Locked
When the status light illuminates, the door is operating.
Adding items
You can add items to the washer after the wash cycle has started , select PAUSE/ CANCEL...
User Guide - Page 26
...-speed spin to wash small loads of 2-3 lightly soiled garments that you set your hot water heater to 120ºF (49ºC) to wash loads of heavy soils and stains. Quick Wash
Use this cycle to avoid chlorine residues on your laundry.
Cycle
Sanitary Whitest Whites Heavy Duty Normal/Casual Quick Wash (2-3 items) Delicate/ Hand Wash Clean Washer Rinse/Spin...
User Guide - Page 27
... wash cycle will be a short tone and the light for that you will hear water spraying and splashing during the Clean Washer ...washing machine. You may hear various sounds when the door is preset to HIGH. Drain without drum movement, to a load using the fabric softener dispenser.
Not all options are available with all cycles.
• See the "Laundry Guide" section for :
• Loads...
User Guide - Page 28
...selected. The washer continues automatically from the washer as soon as in "Cycles."
• ATC works for loads of heavily soiled garments that bleed or fade Light soils
In wash water temperatures ...dispenser drawer.
• Use powdered detergent to keep laundry additives from garments.
Prewash
Use this option for the wash temperature with the same water temperature as it stops....
User Guide - Page 29
... special care items marked "Hand Washable"
Clean Washer No clothes
Rinse & Spin
All loads
Drain & Spin
All loads
Soak
All loads
Delay Wash
AVAILABLE OPTIONS
Extra Rinse
Pre
End of these washer cycles.
CYCLE
SUGGESTED LOAD TYPE
Sanitary
Heavily soiled underwear, towels, work cloths, diapers, etc. LAUNDRY GUIDE
Refer to each of
Wash Cycle Signal
3-11 Listed to the right...
User Guide - Page 30
...If necessary, the cleaning cycle may be run to the next cycle. Select the CLEAN WASHER cycle.
6. This will unlock. Washer Maintenance Procedure
This washer has a special cycle that follows. a) ...washer, it will proceed to cancel the failure code.
This will remain lit.
Pull back the seal/ bellow to inspect all the Cycle lights will flash and the WASH and CONTROLS LOCKED lights...
User Guide - Page 31
Do not use washer again:
1. Wash the parts under running water. When replacing your inlet hoses, record the date of R.V.-type antifreeze in the drum.
2. Put 1 qt (1 L) of replacement. Unplug washer or disconnect power.
4.
Cleaning the exterior
Use a soft damp cloth or sponge to provide ventilation. VACATION, STORAGE, & MOVING CARE
Install and store your ...
User Guide - Page 32
.... Do not use an extension cord. To transport the washer:
1. IMPORTANT: Call service.
Plug in death, fire, or electrical shock.
4. Use 1/2 the manufacturer's recommended amount for a medium sized load.
3-14 Reinstalling the washer
1. Run the washer through the Normal/Ca- Follow the "Installation Instructions" to the rear panel of R.V.-type antifreeze in the upright position...
User Guide - Page 35
...? Wash smaller loads.
• Is the washer door firmly shut? WASHER CONTINUES...washer uses very little water to continue. Replace the fuse, or reset...WASHER OPERATION
WASHER WON'T RUN, FILL, RINSE, OR TUMBLE; Cycle will occur more items or redistribute the load. This is used.
• Is the load balanced? Reinstall hoses, turn on washer? Turn on ? WASHER STOPS
Electrical...
User Guide - Page 80
... and standing status lights. Check resistance of the drive motor. 5. PUMP DRIVE ERROR The pump driver fails to the door switch/lock
unit and Central Control Unit (CCU). Check the MCU by running . 4.
Press PAUSE/CANCEL two times to inlet valves, pressure switch, drain pump and Central Control Unit (CCU).
5. Unplug washer or disconnect power. 3.
Unplug washer or disconnect...
User Guide - Page 81
... door unlock has failed 6 times. Possible Causes/Procedure Door lock mechanism is cleared.
Unplug washer or disconnect power. 3. Check the drive system for powered rotations. Check wire harness connections to the dispenser motor
and Central Control Unit (CCU). 4. LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE
If at the MCU is not mounted upside down . If a failure...
User Guide - Page 88
... bleach.
• If the procedure does not sufficiently improve the machine freshness, please evaluate your installation and usage conditions for better ventilation and drying ...machine will not fill, but the basket will remain lit. b) If any items are detected in the washer, all cycle lights will flash and the WASH and CONTROLS LOCKED lights will rotate while the washer runs...
Similar Questions
Where Is The Filter Located On A Kenmore Washing Machine Model 110 24622300?
(Posted by rlhaan36 8 years ago)
Dishwasher Control Panel - Panel Button Breakage
To whom it may concern, I am inquiring about a dishwasher control panel model#665.13109k902. The pla...
To whom it may concern, I am inquiring about a dishwasher control panel model#665.13109k902. The pla...
(Posted by henrybuswell 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
What Does It Mean When A Kenmore Front Load Washer Model # 48102 Turns Off And O
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
(Posted by kemackey86 11 years ago)
Why Front Load Washer 4044 Won't Start The Cycle?
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
(Posted by martinezmarly 11 years ago)