Kenmore 4810 Support Question
Kenmore 4810 Support Question
Find answers below for this question about Kenmore 4810 - 3.5 cu. Ft. I.E.C. High-Efficiency Washer.Need a Kenmore 4810 manual? We have 2 online manuals for this item!
Question posted by kemackey86 on August 23rd, 2012
What Does It Mean When A Kenmore Front Load Washer Model # 48102 Turns Off And O
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing cycle
Current Answers
Related Kenmore 4810 Manual Pages
Operating Instructions - Page 1
...
o
Hot Cold
WASHER OPERATING iNSTRUCTiONS Model 48102/48106
High 0 ivied0 L0w 0 HangDry 0 NoSpin 0
Heavy Soil/Stain 0 E×traRinse 0
ExtraSpin 0 CycleSignal 0
12hrs 0 8hrsO 4hrs O
DoerLecked 0
AddGarmentO Washing O FinaISpin 0
o 0o
PROGRAM
Before Operating Your Washer
Read your washer Owner's Guide before operating this appliance. Sort laundry into loads that cycle is selected in...
Operating Instructions - Page 2
... seasonal items from closets, or wet loads forgotten in the washer. Wash / Rinse Water Temperatures
Select the wash and rinse water temperatures appropriate for each cycle will continue for 6 minutes followed by...slowly for the load. Use No Spin to your laundry items, all options are important. Cycle Options
To select Heavy Soil/Stain, Extra Spin, Extra Rinse or Cycle Signal, press ...
Operating Instructions - Page 3
... Warm/Warm Hot/Cold Speed High Spin
Medium Spin Low Spin Hang Dry
No Spin Options Cycle Signal
Heavy
Normal
Perm Press
...* Factory Settings
,/ Available settings
** Estimated cycle duration is based on factory settings and does not
include water fill times, out-of-balance or oversudsing corrections.
PN 134906700 (0706)
WASHER SETTINGS CHART
The following chart shows the temperatures,...
Installation Instructions - Page 1
...
WHAT TO DO IF YOU SMELL GAS • Do not try to the washer must conform with local codes and ordinances and the latest edition of the National ...lnstallation Requirements Electrical Requirements Grounding Requirements Water Supply Requirements Drain Requirements Rough-In Dimensions Location Of Your Washer Unpacking Installation Replacement Parts
PAGE
2 2 2 2 2 3 4 4-5 5-6 6
Installation and ...
Installation Instructions - Page 2
... Codes, ANSI/NFPA 70 (latest edition). time delay fuse or circuit breaker.
Since your washer is equipped with a power supply cord having an equipment-grounding conductor and a grounding plug,... the
absence of local codes, with 15 amp.
DRAIN REQUIREMENTS
I /4 in . (229 cm) high standpipe.
Individual, properly polarized and grounded 15 amp. NOTE: Because of eliminating 17 gals (64.3 ...
Installation Instructions - Page 4
...: 2 Iouvered openings each 60 in2(387 cm2), 3 in. (7.6 cm) from top and bottom of door. In an area exposed to protect the floor, lay the washer on it will come in contact with a maximum slope of 1/2 in. In an area (garage or garage-type building) where gasoline of other flammables are...
Installation Instructions - Page 5
... be prevented by the packaging spacers. NOTE: Use only new hoses.
2.
For pedestal installations, See additional installation instructions included with the washer in each end of the water valve.
Pressdown on and check for leaks. Turn the water on alternate corners and sides and feel for best performance of the water
valve.
Installation Instructions - Page 6
...standpipe, inlet hose, laundry tub, etc. Pedestal A pedestal accessory, ModelNo, 48062 (white), 48066(black), specifically designed for this washer are achieved when all ...washer.
Place the hook end of the water.
7. Secure the drain hose with
this washer may occur. Plug the power cord into an outlet.
8. Turn on the inside of use. Run the washer through a complete cycle...
Similar Questions
Distinguishing Different Models Of Kenmoore Washing Machines
How to determine between an 80 series and a 90 series kenmoore washing machine? I was told that the ...
How to determine between an 80 series and a 90 series kenmoore washing machine? I was told that the ...
(Posted by clinebuccie 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
Kenmore Front Load Washer Model # Mfl31245153Drain Hose Has Come Off
I opened the drain pump filter access panel to do regular maintenance. When I opened the panel, th...
I opened the drain pump filter access panel to do regular maintenance. When I opened the panel, th...
(Posted by rsherman33587 11 years ago)
My Washer Doesn't Start A Cycle Properly.
My washer acts like its going to start a cycle the stops and wont continue.
My washer acts like its going to start a cycle the stops and wont continue.
(Posted by evaheimann 13 years ago)