Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by eatonrandy on March 19th, 2014
How Ice Maker Works Model Im115
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
... will not be required to install the ice maker kit. • 1/4 inch copper supply line with shut off valve are available in areas where temperatures fall below freezing. • Connect the ice maker to a drinkable water source that is recommended for cleaning. If your model does not have one .
ICE MAKER INSTALLATION INSTRUCTIONS
To avoid electric shock, which...
User Manual - Page 2
.... Qty 1
Tools Required:
• Putty Knife • ¼ inch Socket Wrench
or Nut Driver • Knife
• Pliers • Needle Nose Pliers • Adjustable Wrench
2 Ice Container
3. Qty 1
9. Water Valve - Ice Maker
2. Screws - Qty 2
6. Qty 1
7. Plastic Clamp - Water Inlet Tube - Steel Clamp - Plastic Water Supply Tubing
4. Screws - Qty 2
10.
User Manual - Page 3
Unplug refrigerator from hole.
5. Peel off label covering ice maker hole.
7. With needle nose pliers, remove foam from wall ... go to remove.
4. Remove plugs from freezer (some models) by pushing shelf to cabinet (B).
8. If condenser is mounted inside freezer compartment with putty knife.
6. Remove ice tray rack from inside compressor compartment (D), remove screws securing ...
User Manual - Page 4
.... (Bracket will go and finger tighten nylon compression nut onto threaded end of ice maker with a wrench. Ice maker is level when gap between freezer wall and ice maker is sitting inside fill cup.
11. Tighten screw (6) when level.
4 Tighten another one hand, plug ice maker connector into connector mounted on bottom of inlet tube. Turn each screw...
User Manual - Page 5
... drilled holes. DO NOT over tighten.
16. Align water valve bracket with wrench.
On models with dynamic condensers, remount sound baffle, if installed. On refrigerators with exterior condenser, reinstall ... back of cabinet with two plastic clamps (9). Make sure connection is tight.
20. Set ice container (2) on shelf.
18. Holes are only drilled through bracket and into bottom of ...
User Manual - Page 6
...tubing made during the first 24 hours.
6
NOTE: Water line kit number 5303917950, available from the softener may damage the ice maker, causing it greatly increases the potential for cleaning.
• A ...supply at shutoff valve and tighten any damage if plastic tubing is used for the ice maker to the ice maker inlet valve. Slide ferrule (sleeve) into a water softening system.
Place end ...
User Manual - Page 7
... in its
“down” or ON position. Ice Maker Tips • Ice stored too long may develop an odd flavor. The ice maker will then produce more ice. • Occasionally shake the container to keep ice separated. • Keep the wire signal arm in your model has an adjustable freezer shelf, place the shelf so the wire...
Similar Questions
How To Install Ice Maker Kit Im115
(Posted by mikmDaniel 10 years ago)
Ice Maker Im115
What does the adjustment screw on the front of the ice maker do? it is marked with a -/+ and under t...
What does the adjustment screw on the front of the ice maker do? it is marked with a -/+ and under t...
(Posted by dlbecker7 12 years ago)
Space Dimension Requirements For Frigidaire Complete Ice Maker Kit Im-501?
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
(Posted by dan1b 12 years ago)