Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by chamja on November 20th, 2013
How Long Before Model Im115 Starts
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by OnlineOutreachSpecialist on November 21st, 2013 11:41 AM
OnlineOutreachSpecialist
Member since:
March 30th, 2011 Points: 2,848,320
Member since:
March 30th, 2011 Points: 2,848,320
Hello chamja, thank you for your post!
Generally speaking, the temperature in your refrigerator determines how long before the ice maker starts producing ice. I would allow approximately 24 hours for temperature to stabilize. I hope this information helps to some degree.
Best regards!
Online Outreach Specialist
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
...compression nut and ferrule • Freezer shelf (Some models not eqipped with shut off valve are available in areas where temperatures fall below freezing. • Connect the ice maker to allow movement for cleaning.
The following items will... is not recommended since it to install the ice maker kit. • 1/4 inch copper supply line with shelf). If your model does not have one .
User Manual - Page 2
Ice Maker
2. Ice Container
3. Qty 2
5. Qty 1
9. Qty 1
Tools Required:
• Putty Knife • ¼ inch Socket Wrench
or Nut Driver • Knife
• Pliers • Needle Nose Pliers &#...
User Manual - Page 3
...from wall outlet.
2. Slowly lift up and pull on back of refrigerator.
3 Peel off label covering ice maker hole.
7. If condenser is tight against back of refrigerator. Unplug refrigerator from hole.
5. Rotate while inserting...locate left until flat surface of hole. Remove ice tray rack from freezer (some models) by pushing shelf to left condenser mounting bracket screw(s).
User Manual - Page 4
....
14. Adjust leveling bracket (7) to level ice maker (1). Push plastic water supply tubing (3) into connector mounted on bottom of inlet tube. Tighten screw (6) when level.
4 9. With ice maker in Step 12.Tighten screws. Make sure water inlet tube (11) is tight.
10. Start two, long, ice maker mounting screws (5) into freezer wall. Ice maker is level when gap between freezer...
User Manual - Page 5
... will go. NOTE: Clean back of water valve. Make sure connection is tight.
20. Set ice container (2) on shelf.
18. Align water valve bracket with exterior condenser, reinstall condenser brackets and tighten down screws.
21. On models with factory drilled holes. Tighten another one half turn with dynamic condensers, remount sound baffle...
User Manual - Page 6
... water supply line made during the first 24 hours.
6 NOTE: Water line kit number 5303917950, available from the ice maker inlet valve at the back of the refrigerator to a household cold water line...supply and flush supply line until water is recommended for on , lower wire signal arm. (See ice maker front cover for the water supply line. Coil excess water supply line (about 2-1/2 turns) behind...
User Manual - Page 7
... following sounds are normal when the ice maker is operating.
• Motor running • Ice loosening from a malfunctioning softener can damage the ice maker. Ice Maker Tips • Ice stored too long may develop an odd flavor. The ice maker will then produce more ice. • Occasionally shake the container to water that water quality determines your model has an adjustable freezer shelf...
Similar Questions
How Long To Harvest Frigidaire Ice Maker
(Posted by pankagopre 10 years ago)
How To Install Ice Maker Kit Im115
(Posted by mikmDaniel 10 years ago)
Space Dimension Requirements For Frigidaire Complete Ice Maker Kit Im-501?
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
(Posted by dan1b 12 years ago)