Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by ChRK on March 24th, 2014
How To Installthe Im115 Ice Maker Kit
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by waelsaidani1 on March 24th, 2014 9:01 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,777
Member since:
May 12th, 2013 Points: 19,501,777
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
...below freezing. • Connect the ice maker to install the ice maker kit. • 1/4 inch copper supply line with shut off valve are available in a kit from electrical power before connecting a ...compression nut and ferrule • Freezer shelf (Some models not eqipped with shelf). ICE MAKER INSTALLATION INSTRUCTIONS
To avoid electric shock, which can cause death or severe personal injury...
User Manual - Page 2
... Clamp - Qty 1
9. Qty 1
11. Water Inlet Tube - Plastic Water Supply Tubing
4. Screws - Qty 2
6. Leveling Bracket Screw - Qty 1
7. Qty 2
10. Leveling Bracket Qty 1
8. Water Valve - Ice Maker
2. Qty 1
Tools Required:
• Putty Knife • ¼ inch Socket Wrench
or Nut Driver • Knife
• Pliers • Needle Nose Pliers • Adjustable Wrench...
User Manual - Page 3
... up and pull on back of refrigerator. Peel off label covering ice maker hole.
7. DO NOT remove compressor sound baffle (A), if installed... cabinet (B).
8. Rotate while inserting tube until right side of shelf is out of refrigerator.
3 Remove ice tray rack from inside compressor compartment (D), remove screws securing sound baffle to left condenser mounting bracket screw(s). If...
User Manual - Page 4
... NOT tighten bracket. (Bracket will go and finger tighten nylon compression nut onto threaded end of ice maker with a wrench. Push plastic water supply tubing (3) into freezer wall. DO NOT over tighten.
12. Start two, long, ice maker mounting screws (5) into water inlet tube (11) as far as it will be tightened later.)
13...
User Manual - Page 5
Set ice container (2) on shelf.
18. Secure plastic water tubing to rear of cabinet with a Phillips® head bit to water valve. Connect wiring harness to drive ...
User Manual - Page 6
...for supply line. • DO NOT install water supply tubing in new plumbing lines may cause ice maker to cycle two or three times before connecting a water supply line to a potable water source...any damage if plastic tubing is used for installing a water supply line.
NOTE: Water line kit number 5303917950, available from electric power supply.
2. Slide ferrule (sleeve) into sink or bucket....
User Manual - Page 7
... is full. Empty the container and be turned off . • The following sounds are normal when the ice maker is operating.
• Motor running • Ice loosening from a malfunctioning softener can damage the ice maker. To stop the ice maker, lift the wire signal arm until the refrigerator is connected to water that water quality determines your...
Similar Questions
How Long Does It Take A Im115 Ice Maker To Make A Tray Of Ice
(Posted by trCA 10 years ago)
How To Install Ice Maker Kit Im115
(Posted by mikmDaniel 10 years ago)
Why Does It Take 24 Hours For Im115 Ice Maker To Work?
(Posted by gsc724 11 years ago)
I Have A Im115 Ice Maker And Need A Wiring Diagram For The Ice Maker
CAN YOU SUPPLY ME A WIRING DIAGRAM FOR ICE MAKER #IM115?
CAN YOU SUPPLY ME A WIRING DIAGRAM FOR ICE MAKER #IM115?
(Posted by KBB244 12 years ago)
Space Dimension Requirements For Frigidaire Complete Ice Maker Kit Im-501?
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
(Posted by dan1b 12 years ago)