Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by crDb on July 27th, 2014
Diagram Of How An Ice Maker Inside A Freezer Is Hooked Uo
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
... shut off valve are available in areas where temperatures fall below freezing. • Connect the ice maker to install the ice maker kit. • 1/4 inch copper supply line with shut off valve • 1/4 inch brass compression nut and ferrule • Freezer shelf (Some models not eqipped with shelf).
Coil enough tubing at the back of 1/4"
plastic...
User Manual - Page 2
...; Knife
• Pliers • Needle Nose Pliers • Adjustable Wrench
2 Use This Page to Identify Parts
1. Qty 2
5. Qty 2
6. Water Valve - Screws - Plastic Water Supply Tubing
4. Ice Container
3. Ice Maker
2.
User Manual - Page 3
....
3 If condenser is out of refrigerator. Peel off label covering ice maker hole.
7. If refrigerator has exterior condenser (C), go to cabinet (B).
8. 1. Slowly lift up and pull on back of hole. Rotate while inserting tube until right side of shelf is mounted inside freezer compartment with putty knife.
6. DO NOT remove compressor sound baffle (A), if...
User Manual - Page 4
... (5) you installed in one half turn with screw (6). Adjust leveling bracket (7) to level ice maker (1). Start two, long, ice maker mounting screws (5) into water inlet tube (11) as far as it will be tightened later.)
13. Ice maker is level when gap between freezer wall and ice maker is same at top and bottom. Tighten another one hand, plug...
User Manual - Page 5
Set ice container (2) on shelf.
18. Push plastic water supply tubing into cabinet.
19. On models ...of water valve. Finger tighten nylon compression nut onto threaded end of cabinet with two plastic clamps (9). See step 5.
5 Reinstall freezer shelf in lower position. Locate factory punched holes at bottom right corner of cabinet with a commercial household cleaner, ammonia or alcohol...
User Manual - Page 6
... inlet and finger tighten compression nut onto valve.Tighten another half turn ice maker on, lower wire signal arm. (See ice maker front cover for on/off position of arm.)
IMPORTANT: It takes .... Connecting Ice Maker to Water Supply
To avoid electric shock, which can be discolored or have poor flavor. Turn OFF water supply at location as shown.
5. NOTE: Water line kit number 5303917950...
User Manual - Page 7
... when the ice maker is operating.
• Motor running • Ice loosening from a malfunctioning softener can damage the ice maker. Rinse well and dry. • Stop the ice maker when cleaning the freezer or for a long period of time, turn the water supply valve to the closed position.
7
Automatic Ice Maker Tips
Remember that is softened. Ice Maker Tips • Ice stored too...
Similar Questions
How To Install Frigidaire Ice Make Im115
(Posted by ADflai 10 years ago)
How To Install Ice Maker Kit Im115
(Posted by mikmDaniel 10 years ago)
Ice Maker Im115
What does the adjustment screw on the front of the ice maker do? it is marked with a -/+ and under t...
What does the adjustment screw on the front of the ice maker do? it is marked with a -/+ and under t...
(Posted by dlbecker7 12 years ago)
Space Dimension Requirements For Frigidaire Complete Ice Maker Kit Im-501?
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
(Posted by dan1b 12 years ago)