Home » D-Link » Hubs & Switches » D-Link 3100 24P

D-Link 3100 24P Support Question

Find answers below for this question about D-Link 3100 24P - DGS Switch - Stackable.
Need a D-Link 3100 24P manual? We have 1 online manual for this item!

D-Link Overview Questions Manuals Reviews Videos Research

Question posted by shsshinde2006 on June 12th, 2011

Dgs 3100 Default Ip?

The person who posted this question about this D-Link product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by kcmjr on June 12th, 2011 11:28 PM

This answer was accepted by the poster of the original question.

kcmjr

Member since:
May 5th, 2011

Points: 4,254,255

1,120
points

This is a managed layer 2 ethernet switch. The Factory default IP address for the Switch is 10.90.90.90. This address will more than likely not be usable in your network, you will need to assign a vaild IP address before using it for the first time. For full programming info you can get a user manual here: http://207.232.83.50/products/view.asp?productid=DGS-3100-24P. It's more detailed than I can go into here without taking up 20 pages.

Licenses & Certifications: Microsoft, Cisco, VMware, Novell, FCC RF & Amateur Radio licensed.

Related D-Link 3100 24P Manual Pages

User Manual - Page 9

Intended Audience The DGS-3100 series/DGS-3100-24TG User Guide contains information for viewing system information, defining IP addresses, managing stacking, defining ports,... Section 6, Monitoring the Device - iii DGS-3100 Series Gigabit Stackable Managed Switch User Manual Device Management Methods The DGS-3100 series and DGS-3100-24TG provide different methods for managing the device...

User Manual - Page 15

NOTE: The Factory default IP address for session connection should be turned off. Please note that the proxy for the Switch is 10.90.90.90. 1 DGS-3100 Series Gigabit Stackable Managed Switch User Manual 1 GETTING STARTED To begin managing the device, simply run the browser installed on the management station and point it to the IP address defined...

User Manual - Page 16

... Baud-Rate option to load normally. DGS-3100 Series Gigabit Stackable Managed Switch User Manual Accessing the Boot/Startup Menu Functions The following configuration functions are : 2400, 4800, 9600, 19200, 38400. During the boot process, after the following message is completed press Ctrl+shift+ (-) within 25 seconds (default), the switch times out and the device continues...

User Manual - Page 17

... the current unit stack ID list, press "1". Press Enter to Managing Stacking for auto-numbering, which is displayed: Set new device Baud rate: _ 2. DGS-3100 Series Gigabit Stackable Managed Switch User Manual The following prompt is displayed: Stack menu [1] Show unit stack id [2] Set unit stack id [3] Back Enter your choice or press 'ESC...

User Manual - Page 18

...DGS-3100 Series Gigabit Stackable Managed Switch... User Manual Using the Web-Based User Interface This section contains information on starting the D-Link Embedded Web Interface. Ensure that pop-up blockers are disabled. The screen captures in the address bar and press Enter. Open an Internet browser. Enter the device IP address in this Guide represent the DGS-3100...

User Manual - Page 22

DGS-3100 Series Gigabit Stackable Managed Switch User Manual Backing up and Restoring Configuration Files The Config Backup and ...the system files are backed up the current configuration files via an TFTP server. The possible field values are : Server IP - The possible field values are Startup Config and Running Config. Specifies the current configuration file type. To back up ...

User Manual - Page 23

... device 9 Define the selected server method fields. To restore the device to the factory default settings: 1. To backup files, click . Resetting the Device The Factory Reset Page restores the factory defaults. Figure 1-4 Factory Reset Page . DGS-3100 Series Gigabit Stackable Managed Switch User Manual 2. Select HTTP or TFTP field. 3. To restore files, click . The Factory...

User Manual - Page 25

...TFTP server. Indicates if the Firmware file is updated. 11 File - DGS-3100 Series Gigabit Stackable Managed Switch User Manual The Firmware Download Page contains the following fields: Field Description HTTP...or specific device. 2. Server IP Address - Indicates the Firmware file that is downloaded to the stack or specific device. Specifies the TFTP Server IP Address from which files are...

User Manual - Page 27

... file. Reboot the system Refreshes device information. Table 1-3. User Interface Buttons 13 DGS-3100 Series Gigabit Stackable Managed Switch User Manual Using the Web System Components The following table contains information regarding the... Modifies configuration Information Resets the factory defaults Find System Reboot Refresh Finds a table entry. Displays table entries.

User Manual - Page 30

...Default Gateway Displays the device default gateway assigned to the feature name. Login Timeout (minutes) Indicates the amount of time after which if no user activity occurs, the device times out. DGS-3100 Series Gigabit Stackable Managed Switch... the Device Status and Quick Configuration Section. 2. IP Address Displays the IP address assigned to viewing the Jumbo Frames settings. Time...

User Manual - Page 32

... to other subnets and other networks. Gateway Defines the default gateway. Click . DGS-3100 Series Gigabit Stackable Managed Switch User Manual Defining IP Addresses The IP Address Page contains fields for assigning IP addresses. IP Address Defines the IP address. The default value is the defined IP address type, define the IP Address field. 4. Management VLAN VID Defines the...

User Manual - Page 41

... stacks have the same configuration and the same IP address. The Stack Master notifies the system administrator...If a stack is there are performed in the Factory Default Mode, the stacking members are reported as the Stack... Since the stacking members started as described in0 - DGS-3100 Series Gigabit Stackable Managed Switch User Manual - Backup Master was not acting as ...

User Manual - Page 48

... Entry Age period, the entry is 300 seconds. The default value is deleted from the table. ARP Aging Time (1-... is 1 - 65535. DGS-3100 Series Gigabit Stackable Managed Switch User Manual ARP Settings The Address Resolution Protocol (ARP) converts IP addresses into physical addresses and maps the IP address to communicate with other hosts only when the IP addresses of its neighbors are...

User Manual - Page 51

... based on their urgency or relevancy. DGS-3100 Series Gigabit Stackable Managed Switch User Manual Managing System Logs System Logs... the Index, Severity, Server IP, Facility, and UDP Port fields. 3. Messages are sent. Server IP Displays the IP address of system logs. UDP...sent to which warning logs are two levels. - The default value is 1 - 65535. The System Log Host ...

User Manual - Page 54

... and time. SNTP Second Server Defines the IP address of primary SNTP server from SNTP server. The Poll Interval default is 60-86400 seconds. Time in seconds)...First Server Description Defines the IP address of secondary SNTP server from a SNTP server. Click Configuration > SNTP Settings > Time Settings. DGS-3100 Series Gigabit Stackable Managed Switch User Manual Polling for Unicast...

User Manual - Page 70

... server. The DHCP automatic configuration update is modified, and the device is the default. 3. The possible field values are saved. The DHCP server maintains the TFTP Server IP address, where the files are :  Enabled - DGS-3100 Series Gigabit Stackable Managed Switch User Manual DHCP Auto Configuration In the DHCP Auto Configuration Page, users can enable...

User Manual - Page 80

... Tag ports. DGS-3100 Series Gigabit Stackable Managed Switch User Manual the ingress port. This process is referred to the 'default.' Any VLAN setting on the switch, then all...example is configured as member to a VLAN (similar to use VLAN segmentation in this table: VLAN Name VID System (default) 1 Switch Ports 5, 6, 7, 8, 21, 22, 23, 24 Engineering 2 9, 10, 11, 12 Marketing 3 13,...

User Manual - Page 147

...Figure 5-6. RADIUS Server Defines the RADIUS server IP addresses. Accounting Port Defines the port used on the server. The default parameters are user-defined, and are defined for...The default port is 1812. Indicates the RADIUS parameters are : First - This key must match the encryption used to newly defined RADIUS servers. 1. DGS-3100 Series Gigabit Stackable Managed Switch User ...

User Manual - Page 156

... Server Host Page contains the following fields: Field Description IP Address Defines the IP address of time that passes, in which no authentication ...Third is the lowest priority and First is the highest priority. DGS-3100 Series Gigabit Stackable Managed Switch User Manual Configuring Authentication Server Hosts The Authentication Server is a...defaults to 1812, TACACS+ port number...

User Manual - Page 181

...enabled only on the DGS-3100-24P and DGS-3100-48P devices. This section includes the following topics:  Defining PoE System Information  Displaying and Editing PoE System Information 167 Powered Devices are devices which receive power from the DGS-3100 series device power supplies, for example IP phones. DGS-3100 Series Gigabit Stackable Managed Switch User Manual 7 MANAGING...