ZyXEL MS-7206S Support and Manuals
Get Help and Manuals for this ZyXEL item
This item is in your list!
View All Support Options Below
Free ZyXEL MS-7206S manuals!
Problems with ZyXEL MS-7206S?
Ask a Question
Free ZyXEL MS-7206S manuals!
Problems with ZyXEL MS-7206S?
Ask a Question
Popular ZyXEL MS-7206S Manual Pages
User Guide - Page 19
... SSH works ...313 40.4.2 SSH Implementation on the Switch 314 40.5 Introduction to HTTPS ...314 40.5.1 HTTPS Example ...315 40.6 Service Access Control 319 40.7 Remote Management 320
Chapter 41 Diagnostic...321
41.1 Diagnostic ...321
Chapter 42 Syslog ...323
42.1 Syslog Overview ...323 42.2 Syslog Setup ...324
42.2.1 Syslog Server Setup 325
MS-7206 User's Guide
19
User Guide - Page 26
...for troubleshooting by an SNMP manager. You could simply restore your password, you know how to manage the MM-7201.
• Web Configurator. Chapter 1 Introducing the MM-7201
In this configuration, the MS-7206 system provides high switching capacity, high port density, and centralized management for firmware upgrades and configuration backup/restore.
See the CLI Reference Guide.
•...
User Guide - Page 62
....
62
MS-7206 User's Guide Name
This field displays the type of power from a Power over , until the system starts up . This field displays the amount of card in the slot. Click a slot number to look at one or more sensors.
PoE Status
Total Power (W)
Consuming Power (W)
Remaining Power (W)
Power Source Status
Power1
Error...
User Guide - Page 66
...the time service protocol that works. When you open this screen. When you enter the time settings manually, the MM-7201 uses the new setting when you turn on the switch, the ... 0:0. Please wait.
Not all time servers support all protocols, so you click Apply. NTP (RFC-1305) is the default value. The switch searches for the timeserver for 60 seconds.... Time.
66
MS-7206 User's Guide
User Guide - Page 77
To open this screen to control the power to the each slot or to change what type of card is in the slot without restarting the system. CHAPTER 11
Slot Setup
11.1 Slot Setup
Use this screen, click Basic Setting > Slot Setup. Figure 23 Slot Setup
MS-7206 User's Guide
77
User Guide - Page 122
...
MS-7206 User's Guide Path cost is turned off or loses power, so use the Save link on a port-by-port basis.
The allowed range is between 0 and 61440 in a switch. The switch... for the specific spanning tree instance. Chapter 16 Spanning Tree Protocol
Table 31 Multiple Spanning Tree Protocol (continued)
LABEL
DESCRIPTION
Bridge Priority
Set the priority of the switch for more...
User Guide - Page 175
... IEEE 802.1p standard that whether the frame carries IEEE 802.1Q tag information. MS-7206 User's Guide
175
SP VID is the VID for the second (service provider's) VLAN tag.
26.3.1 Frame Format
The frame format for .
• On the switch, configure priority level of the following three fields.
Many vendors use 0x8100 or...
User Guide - Page 187
... subscriber devices can set your switch to the associated multicast group.
27.6.2 MVR Modes
You can connect through a port configured as multicast routers or servers) in either dynamic or compatible mode.
If the IGMP report matches one of MVR Ports
In MVR, a source port is a port on the switch, an
MS-7206 User's Guide
187 Figure...
User Guide - Page 196
... in this way (See Section 40.3 on the switch. In essence, RADIUS and TACACS+ authentication both ) and then set up the authentication priority, activate authorization and accounting settings.
196
MS-7206 User's Guide Table 60 RADIUS vs TACACS+
RADIUS
Transport Protocol
UDP (User Datagram Protocol)
Encryption
Encrypts the password sent for authentication.
Figure 84 AAA Server
Client...
User Guide - Page 197
... the navigation panel to display the screen as shown. Click on RADIUS servers. Figure 86 RADIUS Server Setup
MS-7206 User's Guide
197
Figure 85 AAA
28.2.1 RADIUS Server Setup
Use this screen to configure your RADIUS server settings.
Chapter 28 AAA Click Advanced Application > AAA in the AAA screen to view the screen as shown...
User Guide - Page 199
... existing RADIUS accounting server entry from the switch. Click on the top navigation panel to save your TACACS+ server settings.
This entry is not sent over the...accounting server and the switch.
Figure 87 TACACS+ Server Setup
MS-7206 User's Guide
199 Chapter 28 AAA
Table 61 RADIUS Server Setup (continued)
LABEL
DESCRIPTION
Shared Secret
Specify a password (up to 32 ...
User Guide - Page 201
... if you click Apply. Delete
Check this screen to configure authentication, authorization and accounting settings on the AAA Setup link in the AAA screen to remove an existing TACACS+ accounting server entry from the switch. Figure 88 AAA Setup
MS-7206 User's Guide
201 This key is deleted when you want to view the screen as the...
User Guide - Page 273
... change the System Name in Basic Settings > General Setup.
MS-7206 User's Guide
273 The DHCP Relay Agent Information feature adds an Agent Information field to system name set in Basic Settings > General Setup. VLAN ID
(2 bytes) This is always 0 for more details.
Chapter 37 DHCP
37.3.1 DHCP Relay Agent Information
The switch can add information about the source...
User Guide - Page 276
... a management IP address for each VLAN that displays.
Figure 133 DHCP VLAN Setting
276
MS-7206 User's Guide Chapter 37 DHCP
37.4 Configuring DHCP VLAN Settings
Use this screen to configure your DHCP settings based on the switch. Click IP Application > DHCP in the navigation panel, then click the VLAN link In the DHCP Status screen that...
ZyXEL MS-7206S Reviews
Do you have an experience with the ZyXEL MS-7206S that you would like to share?
Earn 750 points for your review!
We have not received any reviews for ZyXEL yet.
Earn 750 points for your review!