ZyXEL MP-7202 Support and Manuals
Get Help and Manuals for this ZyXEL item
View All Support Options Below
Free ZyXEL MP-7202 manuals!
Problems with ZyXEL MP-7202?
Ask a Question
Free ZyXEL MP-7202 manuals!
Problems with ZyXEL MP-7202?
Ask a Question
Popular ZyXEL MP-7202 Manual Pages
User Guide - Page 3
Related Documentation
• MS-7206 Hardware Installation Guide Hardware guide for the MS-7206 system, including the MS-7206S, MI-7248, MI7248PWR, MI-7248TF, MI-7526F, MF-7201, MP-7201, MPC-7202, MP-7202, and MP-7203.
• Command Line Interface (CLI) Reference Guide Line commands offer an alternative to the web configurator and in some cases are necessary to...
User Guide - Page 66
... Time.
66
MS-7206 User's Guide None is recommended that works. New...service protocol that is similar to early fall when many countries set their clocks ahead of seconds since 1970/1/1 at 0:0:0. When you enter the time settings manually, the MM-7201 uses the new setting... value. Not all time servers support all protocols, so you may have to use trial and error to find a protocol that you...
User Guide - Page 77
CHAPTER 11
Slot Setup
11.1 Slot Setup
Use this screen, click Basic Setting > Slot Setup. Figure 23 Slot Setup
MS-7206 User's Guide
77 To open this screen to control the power to the each slot or to change what type of card is in the slot without restarting the system.
User Guide - Page 122
...nonvolatile memory when you make them. Use this row first to set the common settings and then make some settings the same for the specific spanning tree instance. Active Priority
Path Cost
Add
Cancel Instance VLAN ...that port.
It is between 0 and 61440 in the MST instance.
122
MS-7206 User's Guide This field displays the VID (or VID ranges) to participate in increments of the switch for...
User Guide - Page 175
...double-tagged" 802.1Q frame (service provider) is shown next. VID is the service provider VLAN stacking tag type.
MS-7206 User's Guide
175 SP TPID (Service Provider Tag Protocol Identifier) is ...service provider to all incoming frames on the service provider's edge devices (1 and 2 in the Port Setup screen.
• "0" is the lowest priority level and "7" is a standard Ethernet type code...
User Guide - Page 187
...hidden from other multicast devices (such as the receiver on the switch, an
MS-7206 User's Guide
187 Chapter 27 Multicast
MVR.
If the IGMP report matches one of MVR Ports
In MVR,...multicast devices to update the multicast forwarding table to forward or not forward multicast traffic to the receiver ports. In this case, you must manually configure the forwarding settings on the ...
User Guide - Page 196
...
UDP (User Datagram Protocol)
Encryption
Encrypts the password sent for authentication.
TACACS+ TCP (Transmission Control Protocol)
All communication between RADIUS and TACACS+. In essence, RADIUS and TACACS+ authentication both ) and then set up the authentication priority, activate authorization and accounting settings.
196
MS-7206 User's Guide
Chapter 28 AAA
28.1.2 on the switch...
User Guide - Page 197
... server settings. Chapter 28 AAA Click Advanced Application > AAA in the AAA screen to view the screen as shown. See Section 28.1.2 on page 196 for more information on the RADIUS Server Setup link in the navigation panel to display the screen as shown.
Figure 86 RADIUS Server Setup
MS-7206 User's Guide
197...
User Guide - Page 199
...settings. Click on the TACACS+ Server Setup link in the AAA screen to the switch's run-time memory.
Chapter 28 AAA
Table 61 RADIUS Server Setup (continued)
LABEL
DESCRIPTION
Shared Secret
Specify a password... screen afresh.
28.2.2 TACACS+ Server Setup
Use this box if you are done configuring. Figure 87 TACACS+ Server Setup
MS-7206 User's Guide
199
Delete
Check this screen to the...
User Guide - Page 201
...authentication, authorization and accounting settings on the switch. The switch loses these changes if it is deleted when you click Apply.
Click on the AAA Setup link in the AAA... from the switch. Figure 88 AAA Setup
MS-7206 User's Guide
201 Chapter 28 AAA
Table 62 TACACS+ Server Setup (continued)
LABEL
DESCRIPTION
Shared Secret
Specify a password (up to 32 alphanumeric characters) as...
User Guide - Page 273
... switch sends to a DHCP server.
The DHCP server can change the System Name in Basic Settings > General Setup.
Information
(up to 64 bytes) This optional, read-only field is always 0 for more details. MS-7206 User's Guide
273 You can then provide an IP address based on this option.
This helps provide authentication...
User Guide - Page 276
Figure 133 DHCP VLAN Setting
276
MS-7206 User's Guide Click IP Application > DHCP in the navigation panel, then click the VLAN link In the DHCP Status screen that you want to configure DHCP settings for VLANs.
Note: You must set up a management IP address for each VLAN that displays.
Chapter 37 DHCP
37.4 Configuring...
User Guide - Page 279
Figure 135 DHCP VLAN Setting Example
MS-7206 User's Guide
279
Chapter 37 DHCP
In the DHCP VLAN Setting screen, set the DHCP Status to Server and configure two DHCP client IP address pools for the two networks. The following shows an example.
User Guide - Page 386
..., 158 cloning a port See port cloning 348 cluster management 327, 328 and switch passwords 333 cluster manager 327, 333 cluster member 327, 333 cluster member firmware upgrade 330 network example 328 setup 332 specification 327 status 328 switch models 327 VID 333 web configurator 329 cluster manager 327 cluster member 327 Common and Internal Spanning Tree...
User Guide - Page 391
... 302 and MIB 302 and security 303 authentication 309 communities 308 management model 302 manager 302 MIB 303 network components 302 object variables 302 protocol operations 302 security 309 setup 310 traps 303 version 3 303 versions supported 301 SNMP traps 303 setup 310 supported 303, 304, 305, 307 Spanning Tree Protocol (STP) 105 SPQ (Strict...
ZyXEL MP-7202 Reviews
We have not received any reviews for ZyXEL yet.