Yamaha RX-V495RDS Support and Manuals
Get Help and Manuals for this Yamaha item
View All Support Options Below
Free Yamaha RX-V495RDS manuals!
Problems with Yamaha RX-V495RDS?
Ask a Question
Free Yamaha RX-V495RDS manuals!
Problems with Yamaha RX-V495RDS?
Ask a Question
Yamaha RX-V495RDS Videos
tonsil voyager 350 yamaha rx-v495rds koda sw 15a
Duration: 3:27
Total Views: 854
Duration: 3:27
Total Views: 854
Popular Yamaha RX-V495RDS Manual Pages
Owner's Manual - Page 3
... UNIT 21
q Basic Operation
BASIC OPERATIONS 26 TUNING OPERATIONS 30 RECEIVING RDS STATIONS 35 SETTING THE SLEEP TIMER 40
q Information about DSP
USING THE DIGITAL SOUND FIELD PROCESSOR (DSP 41
q Advanced Information
ADJUSTMENTS IN THE "SET MENU" MODE 47
q Remote Control Transmitter
REMOTE CONTROL TRANSMITTER 49 SETUP CODES 56
TROUBLESHOOTING 57 SPECIFICATIONS 59
LIST OF MANUFACTURER...
Owner's Manual - Page 4
...Model
IMPORTANT THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE...TROUBLESHOOTING" section regarding common operating errors before starting the audio source play. Install this manual carefully. YAMAHA...set the VOLUME control to the terminal which is marked with chemical solvents; If these openings, and install....
13. Special Instructions for future reference....
Owner's Manual - Page 7
...higher frequencies, and press the DOWN side to tune in to automatic or manual. Press it again to set this button so that the "AUTO TUNING" indicator goes off , "EXT..., this unit consumes a very small quantity of power to receive infrared-signals from the remote control transmitter.
2 Remote control sensor
This receives signals from the remote control transmitter.
3 Display
This shows various...
Owner's Manual - Page 8
...by INPUT.
8 t A/B/C/D/E
Press this button is pressed, the unit is set both A and B) to the ON position for sound imbalance caused by pressing... the OFF position.
o RDS MODE
When an RDS station is received, pressing this button to the OFF position and switch off the ...or CT mode (if the station employs those RDS data services) in turn. k VIDEO AUX terminals
Connect an auxiliary ...
Owner's Manual - Page 10
... component selector has been pressed.
3 TEST
Press this button to output the test tone for each speaker. * It only...the remote control transmitter. (The proper code must be set for a YAMAHA component, this button switches between the ...set the SLEEP timer.
8 PRG+, PRG- These buttons are used to select a preset station. * They only function when AMP on and standby mode.
See "SETUP CODES...
Owner's Manual - Page 11
...2) These buttons are for adjusting various settings. * They only function when AMP, DVD MENU or CBL/ DBS on the component selector has been pressed. r Operation buttons1)/Setup buttons2)
1) These buttons function as ... TV on the component selector has been pressed.
2) This button is used to clear the settings. * It only functions when DVD MENU on the component selector has been pressed.
3) This...
Owner's Manual - Page 12
... Best results, however, are used in power amplifier. Note: Set the CNTR (CENTER SPEAKER) mode to use high-performance models that of the 5-speaker configuration. If for some reason it ...speakers, rear speakers and a center speaker. SPEAKER SETUP
SPEAKERS TO BE USED
This unit is designed to choose the convenience of a YAMAHA Active Servo Processing Subwoofer System, which has its own...
Owner's Manual - Page 14
... LD player, etc. Also, refer to the owner's manual for turntable use)
Connecting the ground (earth) wire of this unit.
model 1 SWITCHED OUTLET
Use these to connect the power cords ... will normally minimize hum, but in this unit and other components, be sure all connections have YAMAHA components numbered as !, #, $, etc. CONNECTIONS
Never plug in some cases, better results may ...
Owner's Manual - Page 16
... If your DVD (LD) player, TV/DBS tuner, etc. are not being used in the following order of priority with the input mode set to the AUTO position: 1 COAXIAL terminal 2 OPTICAL terminal 3 Analog terminal • All digital audio signal input terminals are applicable to the ... unit's COAXIAL and/or OPTICAL digital signal input terminals. DVD or LD player
TV/DBS tuner
(Europe model)
16
Owner's Manual - Page 19
... Center: The impedance of each speaker must be 8 Ω or higher.
IMPEDANCE SELECTOR (Europe model)
Select the position whose requirements your speaker system meets.
(Upper position)
Main:
If you use...
19 Center: The impedance of each speaker must be 6 Ω or higher. If so, set the switch to either end fully when this unit is pressed, the IMPEDANCE SELECTOR switch may be...
Owner's Manual - Page 30
... more.
* If the tuning search does not stop at the desired station (because the signal from the station you must tune in manually to select is shown on
the display.
Front panel
Confirm that employs the PS data service is being received, the station name is weak, you want to the desired station.
Owner's Manual - Page 52
... previous track. SKIP+ This button skips to the owner's manual for a YAMAHA CD player, this button turns on .
Press CD. INPUT...- The button functions as PAUSE/STOP* for operating YAMAHA CD player under factory setting. STOP This button stops operation.
The lightly marked ...to find the point from which you have preset the code for details of each component. Please refer to the next...
Owner's Manual - Page 56
... third) VCR. If the VCR cannot be used . Returning to the factory-set codes
Component selector Component Code
TV
TV
0101
CBL/DBS DBS tuner 0006
VCR
VCR
0002
DVD/LD DVD player 0008 YAMAHA
CD
CD player 0005 YAMAHA
TAPE/MD Tape deck 0004 YAMAHA
We recommend that you write all components to the factoryset...
Owner's Manual - Page 57
...set off . No sound from the turntable to the GND terminal. CAUSE The power cord is not plugged in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service... the AC outlet. Set the unit in the standby mode. If the problem persists, the cords .... Set the unit in the power cord. Use a different sound field program.
English
TROUBLESHOOTING
If...
Owner's Manual - Page 58
...terminals. Make additional connections between the analog terminals. Use the manual tuning method. This will result from the TV. Set the code again. The desired station cannot be controlled. The DVD/LD... cannot be tuned in the SET MENU is set is noisy.
The desired station cannot be recorded on a tape deck or MD recorder connected to the instruction for the source being used ...
Yamaha RX-V495RDS Reviews
We have not received any reviews for Yamaha yet.