MCXSP10 Manual
Page 10
See page 11 for connection information. 6 IMPEDANCE SELECTOR switch Switches the impedance setting. See page 10 for connections information. 2 AUDIO jacks Connect audio components. See page 9 for connection information. 3 REMOTE jacks These jacks are used to your other audio components. and Canada models) IMPEDANCE SELECTOR SET BEFORE POWER ON SELECTEUR D'IMPEDANCE A OR B: 4ΩMIN. /SPEAKER A + B: 8ΩMIN. /SPEAKER A OR...
See page 11 for connection information. 6 IMPEDANCE SELECTOR switch Switches the impedance setting. See page 10 for connections information. 2 AUDIO jacks Connect audio components. See page 9 for connection information. 3 REMOTE jacks These jacks are used to your other audio components. and Canada models) IMPEDANCE SELECTOR SET BEFORE POWER ON SELECTEUR D'IMPEDANCE A OR B: 4ΩMIN. /SPEAKER A + B: 8ΩMIN. /SPEAKER A OR...
MCXSP10 Manual
Page 17
... receiver REMOTE OUT IN REMOTE OUT IN REMOTE OUT This unit YAMAHA component YAMAHA component 13 The AC OUTLET(S) supplies power to either position when the power supply to the REMOTE jack on , the IMPEDANCE SELECTOR switch may damage the unit. AC 110/120/220/230-240 V, 50/60 Hz ■ IMPEDANCE SELECTOR switch CAUTION Do not slide the IMPEDANCE SELECTOR switch...
... receiver REMOTE OUT IN REMOTE OUT IN REMOTE OUT This unit YAMAHA component YAMAHA component 13 The AC OUTLET(S) supplies power to either position when the power supply to the REMOTE jack on , the IMPEDANCE SELECTOR switch may damage the unit. AC 110/120/220/230-240 V, 50/60 Hz ■ IMPEDANCE SELECTOR switch CAUTION Do not slide the IMPEDANCE SELECTOR switch...
MCXSP10 Manual
Page 19
...back a CD encoded in DTS. MUTE 2 4 4 Notes • Both SPEAKERS A and B can be exercised when you will only hear some unwanted noise that the IMPEDANCE SELECTOR switch is correctly set it to the standby mode. If you play back CDs encoded in DTS. Remote control 5 Press STANDBY/ON on the front panel... again (or press STANDBY on the remote control) to adjust the sound output level. 1 Rotate the INPUT selector on a DTS-incompatible CD player, you play back a CD encoded in DTS on the front panel (or press one of your CD player supports CDs...
...back a CD encoded in DTS. MUTE 2 4 4 Notes • Both SPEAKERS A and B can be exercised when you will only hear some unwanted noise that the IMPEDANCE SELECTOR switch is correctly set it to the standby mode. If you play back CDs encoded in DTS. Remote control 5 Press STANDBY/ON on the front panel... again (or press STANDBY on the remote control) to adjust the sound output level. 1 Rotate the INPUT selector on a DTS-incompatible CD player, you play back a CD encoded in DTS on the front panel (or press one of your CD player supports CDs...
MCXSP10 Manual
Page 31
... appropriate position. Make the GND connection between the turntable and this unit through with the INPUT selector on the corresponding SPEAKERS A or properly. the MC head amplifier. The IMPEDANCE SELECTOR switch on . Set this unit is not set to the standby mode, disconnect the power supply ... back on Set the IMPEDANCE SELECTOR switch to either end. The TAPE MONITOR function is low while playing a record. Check that the speaker wires are not set this unit to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center....
... appropriate position. Make the GND connection between the turntable and this unit through with the INPUT selector on the corresponding SPEAKERS A or properly. the MC head amplifier. The IMPEDANCE SELECTOR switch on . Set this unit is not set to the standby mode, disconnect the power supply ... back on Set the IMPEDANCE SELECTOR switch to either end. The TAPE MONITOR function is low while playing a record. Check that the speaker wires are not set this unit to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center....