Owner's Manual
Page 3
...and the monitor signal from BRIDGE jack. Monitor+monaural main The main monaural mix signal is suitable for a wide range of the EMX2000 and enjoy long, trouble-free performance, please read this owner's manual carefully, and keep it in energy cost and to less... or ambience to vocals or instrumental sounds. • The EMX2000 has implemented "EEEngine", Yamaha's epochal amp drive technology to the amp. • A digital effect with sixteen selectable effect types is very useful for purchasing the Yamaha EMX2000 Powered Mixer. The mixer also has ample power, with a maximum output of 200 ...
...and the monitor signal from BRIDGE jack. Monitor+monaural main The main monaural mix signal is suitable for a wide range of the EMX2000 and enjoy long, trouble-free performance, please read this owner's manual carefully, and keep it in energy cost and to less... or ambience to vocals or instrumental sounds. • The EMX2000 has implemented "EEEngine", Yamaha's epochal amp drive technology to the amp. • A digital effect with sixteen selectable effect types is very useful for purchasing the Yamaha EMX2000 Powered Mixer. The mixer also has ample power, with a maximum output of 200 ...
Owner's Manual
Page 9
... phantom power supply on . The final level of this control does not affect signals that is a mix of the signals input from the mixer section to the power amp section. Z PHONES/C.R.OUT (headphones/control room out) control This knob adjusts the level of the signal monitored via the ... Select one speaker to play a loud sound. The final level of these knobs adjust the input sensitivity of the EMX2000 is turned on / off for the MIC input jacks for channels 1~8. EMX2000-Owner's Manual Use a screwdriver of a width of this signal is adjusted by the master ST 1 fader. • ...
... phantom power supply on . The final level of this control does not affect signals that is a mix of the signals input from the mixer section to the power amp section. Z PHONES/C.R.OUT (headphones/control room out) control This knob adjusts the level of the signal monitored via the ... Select one speaker to play a loud sound. The final level of these knobs adjust the input sensitivity of the EMX2000 is turned on / off for the MIC input jacks for channels 1~8. EMX2000-Owner's Manual Use a screwdriver of a width of this signal is adjusted by the master ST 1 fader. • ...
Owner's Manual
Page 11
..., such as a tape deck, to adjust the final level of the signal output from this jack. Connect an external mixer output here. The nominal output level is +4 dB. 0 MONO (monaural) jack This phone jack mixes the STEREO bus signals ...3mW when headphones are used to input line-level signals to connect stereo outputs of a sub mixer. C FOOT SW (foot switch) jack A separately sold Yamaha FC5 foot switch can be connected to this jack so you insert a plug into this jack.... are connected, and +4 dB when a line-level device of a monitor system is connected. EMX2000-Owner's Manual
..., such as a tape deck, to adjust the final level of the signal output from this jack. Connect an external mixer output here. The nominal output level is +4 dB. 0 MONO (monaural) jack This phone jack mixes the STEREO bus signals ...3mW when headphones are used to input line-level signals to connect stereo outputs of a sub mixer. C FOOT SW (foot switch) jack A separately sold Yamaha FC5 foot switch can be connected to this jack so you insert a plug into this jack.... are connected, and +4 dB when a line-level device of a monitor system is connected. EMX2000-Owner's Manual
Owner's Manual
Page 19
...s Output specifications Output terminal Actual source impedance For use with nominal Output level Nominal Max. OUT for PHONES for C. before cliping Connectors on mixer MIC INPUT (1-8) MAX MIN LINE INPUT (1-8) MAX MIN ST INPUT (9-12) MAX MIN ST SUB IN (1, 2) TAPE IN (L, R) CH INSERT IN...V) PHONO JACK CH INSERT OUT (1-4) 600Ω 10 kΩ Lines 0 dB (775 mV) +20 dB (7.75 V) PHONE JACK1 PHONES/ C. EMX2000-Owner's Manual Sensitivity is the lowest level that can produce an output of +4 dB (1.23 V) or the nominal output level when the unit is referenced...
...s Output specifications Output terminal Actual source impedance For use with nominal Output level Nominal Max. OUT for PHONES for C. before cliping Connectors on mixer MIC INPUT (1-8) MAX MIN LINE INPUT (1-8) MAX MIN ST INPUT (9-12) MAX MIN ST SUB IN (1, 2) TAPE IN (L, R) CH INSERT IN...V) PHONO JACK CH INSERT OUT (1-4) 600Ω 10 kΩ Lines 0 dB (775 mV) +20 dB (7.75 V) PHONE JACK1 PHONES/ C. EMX2000-Owner's Manual Sensitivity is the lowest level that can produce an output of +4 dB (1.23 V) or the nominal output level when the unit is referenced...