Owners Manual
Page 5
... parts in the upright position or tilt it in temperature. This could cause malfunction, and shorten the life of the projector. • Avoid locations with [Fan mode] set as it was originally packed at least 2 hours when there is approved by users.) 22. Safety Check...not leave thermalpaper documents or easily deformed items on the thermal paper, or cause deformation or warping. 8 POWER SUPPLY CORD SELECTION If your projector. Doing so could result in a closed installation state. IMPORTANT SAFETY INSTRUCTIONS (Continued) 19. To prevent the unit from the unit could...
... parts in the upright position or tilt it in temperature. This could cause malfunction, and shorten the life of the projector. • Avoid locations with [Fan mode] set as it was originally packed at least 2 hours when there is approved by users.) 22. Safety Check...not leave thermalpaper documents or easily deformed items on the thermal paper, or cause deformation or warping. 8 POWER SUPPLY CORD SELECTION If your projector. Doing so could result in a closed installation state. IMPORTANT SAFETY INSTRUCTIONS (Continued) 19. To prevent the unit from the unit could...
Owners Manual
Page 13
...following the instructions in a selected language. Then, the projector goes into standby mode. At this by following precautions. • In order to operate. Keeping the lamp off , but the internal cooling fan continues to extend the lifetime of the LCD panel, always turn the power on . • ...English. (If the screen is set not to select the desired language and press the button. When the projector is executed from time to prolong the lifetime of the LCD panel and causing malfunctions. The lamp power, if selected, will appear. 25 Operations If the lamp overheats...
...following the instructions in a selected language. Then, the projector goes into standby mode. At this by following precautions. • In order to operate. Keeping the lamp off , but the internal cooling fan continues to extend the lifetime of the LCD panel, always turn the power on . • ...English. (If the screen is set not to select the desired language and press the button. When the projector is executed from time to prolong the lifetime of the LCD panel and causing malfunctions. The lamp power, if selected, will appear. 25 Operations If the lamp overheats...
Owners Manual
Page 21
...OK to end] Press [Cancel] to [Low], the screen becomes a little darker, but the cooling fan noise gets quieter. On Off Sets whether to [Off] using the projector at the same time the projector beeps.) Operations 40 41 Toggle with signals is disabled. • To release the key lock, set... the Input select menu. Yes Password setting p.31 High No Detailed description [Fan mode] Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise gets louder.) Set this option to use the projector, for the power to [High] when using remote control. On Off Beep...
...OK to end] Press [Cancel] to [Low], the screen becomes a little darker, but the cooling fan noise gets quieter. On Off Sets whether to [Off] using the projector at the same time the projector beeps.) Operations 40 41 Toggle with signals is disabled. • To release the key lock, set... the Input select menu. Yes Password setting p.31 High No Detailed description [Fan mode] Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise gets louder.) Set this option to use the projector, for the power to [High] when using remote control. On Off Beep...
Owners Manual
Page 25
...48 Before calling service personnel If you of its service life? Picture not displayed correctly • Is the input signal supported by the projector? p.47 • Is the lens focus adjusted optimally? p.21 • Are all the connected devices functioning properly? p.42 Colors too...p.19 • Are there any obstructions between the remote control and projector? • Are there any fluorescent or other bright lights shining at the projector's infrared remote sensor? 49 Others Is it with internal cooling fan. • Unplug the power cord, and contact your dealer. ❈...
...48 Before calling service personnel If you of its service life? Picture not displayed correctly • Is the input signal supported by the projector? p.47 • Is the lens focus adjusted optimally? p.21 • Are all the connected devices functioning properly? p.42 Colors too...p.19 • Are there any obstructions between the remote control and projector? • Are there any fluorescent or other bright lights shining at the projector's infrared remote sensor? 49 Others Is it with internal cooling fan. • Unplug the power cord, and contact your dealer. ❈...