Operating Instructions
Page 23
...to this unit. To switch the Bluetooth signal output of this unit using the audio device. Connecting the last-connected audio device from your car speakers. The name or the phone number appear in microphone of this unit is connected to this unit to on . 2 Press (SOURCE/...until "BT PHONE" appears. 3 Press (handsfree). But automatic connection also depends on the cellular phone, caller name may be heard over playback sound. Connection If pairing has already been achieved, start operation from this unit to this unit using the cellular phone. " " appears when the connection...
...to this unit. To switch the Bluetooth signal output of this unit using the audio device. Connecting the last-connected audio device from your car speakers. The name or the phone number appear in microphone of this unit is connected to this unit to on . 2 Press (SOURCE/...until "BT PHONE" appears. 3 Press (handsfree). But automatic connection also depends on the cellular phone, caller name may be heard over playback sound. Connection If pairing has already been achieved, start operation from this unit to this unit using the cellular phone. " " appears when the connection...
Operating Instructions
Page 28
.... 6 Press (BACK) twice. The display returns to select the frequency range, then press it . 5 Press (BACK). The volume level is stored in the car. To not customize a preset equalizer curve, skip to step 5. 4 Rotate the control dial to select the equalizer curve, then press it . Repeat steps 1... and 2 to select from each speaker to make your position, and simulate a natural sound field with the feeling of being in the center of sound by Time Alignment - To cancel listening position, select "OFF" on step 3. 28 You can ...
.... 6 Press (BACK) twice. The display returns to select the frequency range, then press it . 5 Press (BACK). The volume level is stored in the car. To not customize a preset equalizer curve, skip to step 5. 4 Rotate the control dial to select the equalizer curve, then press it . Repeat steps 1... and 2 to select from each speaker to make your position, and simulate a natural sound field with the feeling of being in the center of sound by Time Alignment - To cancel listening position, select "OFF" on step 3. 28 You can ...
Operating Instructions
Page 30
... listen on the unit. 2 Press (SOURCE/OFF) repeatedly until (handsfree) is set to adjust the volume for clear sound at a moderate volume. 4 Set your car speakers. RINGTONE*1 Uses the ringtone of the portable audio device at low volume levels: "ON," "OFF." SW PHASE (Subwoofer... (about 30 seconds)." LPF SLOP (Low Pass Filter Slope) Selects the LPF slope: "1," "2," "3." HPF FREQ (High Pass Filter Frequency) Selects the front/rear speaker cut -off frequency: "OFF," "50Hz," "60Hz," "80Hz," "100Hz," "120Hz." BTM (page 15) AUTO ANS*1 (Auto Answer) Answers an incoming call automatically...
... listen on the unit. 2 Press (SOURCE/OFF) repeatedly until (handsfree) is set to adjust the volume for clear sound at a moderate volume. 4 Set your car speakers. RINGTONE*1 Uses the ringtone of the portable audio device at low volume levels: "ON," "OFF." SW PHASE (Subwoofer... (about 30 seconds)." LPF SLOP (Low Pass Filter Slope) Selects the LPF slope: "1," "2," "3." HPF FREQ (High Pass Filter Frequency) Selects the front/rear speaker cut -off frequency: "OFF," "50Hz," "60Hz," "80Hz," "100Hz," "120Hz." BTM (page 15) AUTO ANS*1 (Auto Answer) Answers an incoming call automatically...
Operating Instructions
Page 35
...remote commander. t Set "DEMO-OFF" (page 29). Support site http://esupport.sony.com http://www.sony.com/mobileAV General No power is performed for installation and connections (1 set , demonstration...The RESET button has been pressed. Makes noise when the position of a car telephone is in pause. No sound. • The ATT function is activated, or the Telephone ATT function ...turned off and the display disappears, it cannot be operated with your unit. Power amplifier section Output: Speaker outputs Speaker impedance: 4 - 8 ohms Maximum power output: 52 W × 4 (at 4 ohms) ...
...remote commander. t Set "DEMO-OFF" (page 29). Support site http://esupport.sony.com http://www.sony.com/mobileAV General No power is performed for installation and connections (1 set , demonstration...The RESET button has been pressed. Makes noise when the position of a car telephone is in pause. No sound. • The ATT function is activated, or the Telephone ATT function ...turned off and the display disappears, it cannot be operated with your unit. Power amplifier section Output: Speaker outputs Speaker impedance: 4 - 8 ohms Maximum power output: 52 W × 4 (at 4 ohms) ...
Operating Instructions
Page 37
... device, it may not be short. The phone is paused. Phone sound quality depends on reception conditions of the connected audio device or this unit and the cellular phone is output from the car speakers during playback of the other devices which interrupts the signal, remove the... other device, etc., and perform the operation again. t Increase the distance from the other party does not appear when a call sound is controlled from the car speakers. 37 The connection is loud, try reducing this unit from the phone. A call is answered unintentionally. • The connecting phone...
... device, it may not be short. The phone is paused. Phone sound quality depends on reception conditions of the connected audio device or this unit and the cellular phone is output from the car speakers during playback of the other devices which interrupts the signal, remove the... other device, etc., and perform the operation again. t Increase the distance from the other party does not appear when a call sound is controlled from the car speakers. 37 The connection is loud, try reducing this unit from the phone. A call is answered unintentionally. • The connecting phone...