Sharp XL-UH250 Support and Manuals
Get Help and Manuals for this Sharp item
This item is in your list!
View All Support Options Below
Free Sharp XL-UH250 manuals!
Problems with Sharp XL-UH250?
Ask a Question
Free Sharp XL-UH250 manuals!
Problems with Sharp XL-UH250?
Ask a Question
Most Recent Sharp XL-UH250 Questions
How Do I Reset Speaker Abnormal R B Protection On A Xl-uh250.
I chek the fuses and they are good. I read page 2-4 about Speaker abnormal detection and +B protecti...
I chek the fuses and they are good. I read page 2-4 about Speaker abnormal detection and +B protecti...
(Posted by pkirouac 2 years ago)
Popular Sharp XL-UH250 Manual Pages
Service Manual - Page 1
... Be sure to change without notice. XL-UH250
SERVICE MANUAL
No. GENERAL DESCRIPTION [1] Important Service Safety Precaution 1-1 [2] Specifications 1-1 [3] Names Of Parts 1-2
CHAPTER 2. MECHANICAL DESCRIPTION [1] Removing And Reinstalling The Main Parts
3-1 [2] Disassembly 3-2
CHAPTER 5. BLOCK DIAGRAM [1] Block Diagram 4-1
PARTS GUIDE
Parts marked with specified ones for maintaining...
Service Manual - Page 2
...Repairing with the lead-free solder, apply lead-free wire solder. If a different type of solder stays on the tip of the soldering bit, it has poor solder wettability, you to use of it with the PWB for servicing
Ref No. Be careful when replacing parts with lead-free solder. Parts...service manuals... XL-UH250
...model employs lead-free solder. However, since the land may be easily corrected.
Service Manual - Page 3
...65 535. GENERAL DESCRIPTION
XL-UH250
[1] Important Service Safety Precaution
CAUTION : "These servicing instructions are qualified to do not perform any circuit should be attempted. 2.
ATTENTION: POUR ASSURER UNE LONGUE PROTECTION CONTRE UN INCENDIE, REMPLACER SEULEMENT PAR UN FUSIBLE DE TYPE F801 , F802, ,F805 4A, 125V/ F803 ,F804 2A, 125V FUSES.
[2] Specifications
General
Power source...
Service Manual - Page 7
...CLV Servo ON > key input. Reading Sub-code and Display key input. key input. Start Auto Adjustment at current pick-up location. [2] Test Mode • Setting the test mode During stand-by mode, ... ON > key input.
STOP and return to enter the test mode.\
XL-UH250
Step 1 Step 2 Step 3 Step 4 Step 5
CD
TE ST
OPEN/CLOSE operation is using manual. > key input. IL isn't done IL isn't done
2 - ...
Service Manual - Page 8
XL-UH250
STOP and return to Step 1
Note
Sliding the PICKUP with , > button can be set / >> for more than RW Judgement) = DA : XX - XXXX
key input. XXXX
i) Focus Error
(Other than 1 sec, it directly
To cancel: Power OFF
2 - 3 STOP and return to Step 1 Everytime > key input
a) Focus Balance
= FB : XX
b) Focus Gain
= FG : XX
c) ...
Service Manual - Page 9
...' will flashing as "XL H****" and " FW****V**".
3. Speaker abnormal detection and +B PROTECTION display
In case speaker abnormal detection or +B PROTECTION had been detected for transporting. Example:In case of 'ER-CD**'. 'ER-CD**' will be display when error had occurred, the unit will automatically enter to be taken after set tapering/parts replacement. 1. FM 87.50...
Service Manual - Page 12
XL-UH250
3
143 APPLY GREASE SC141 112
PULL THE LEVER UNITIL REACH THE ARROW MARK
2 - 7
Service Manual - Page 13
XL-UH250
4
FIGURE 1 152
118
FIGURE 2
142
APPLY GREASE SC141
SLOT CLAMP SWITCH ARM INSIDE BASE SLOT
HALF GEAR MUST BE ARRANGED AS SHOWN
2 - 8
Service Manual - Page 14
XL-UH250
5
APPLY GREASE SC141 AT BOTTOM SIDE OF GEAR FOLLOW MARKING (REFER TO GRAY AREA) NO NEED TO APPLY GREASE AT BOTTOM SIDE
CORRECT
FIGURE 1
BLACK MARK
APPLY GREASE SC141 AT TOP SIDE OF GEAR FOLLOW MARKING (REFER TO GRAY AREA)
127
IF DIRECTION IS OTHER THAN DIRECTION SHOWN IN FIGURE 1, IT IS INCORRECT 128
INCORRECT
2 - 9
Service Manual - Page 15
XL-UH250
6
APPLY GREASE SC141 AT HALF GEAR AREA
ROTATE CLOCKWISE UNTIL REACH HERE (MAXIMUM)
129
2 - 10
Service Manual - Page 17
XL-UH250
8
THE SHOWN AREA MUST FREE FROM GREASE
GREASE SC141 APPLICATION LENGTH GREASE APPLICATION PORTION
CORRECT
INCORRECT
124
131 SHOWN HOLE MUST FACING ARROW DIRECTION
2 - 12
Service Manual - Page 18
XL-UH250
9
138 126
125
TR-RE JOINT GEAR C
APPLY GREASE SC141 AT BOTTOM SIDE ONLY
APPLY GREASE SC141 ONLY AT TOP SIDE GEAR
MUST BE FIXED ACCORDINGLY TO THE HOLE'S
2 - 13
Service Manual - Page 95
... safety and performance of XL-UH250 (main unit) and CP-UH250 (speaker system).
The contents are important for maintaining the safety of the set . ASSEMBLY (Not Replacement Item)
[15] OTHER SERVICE PARTS
Parts marked with specified ones for after sales service only. SHARP CORPORATION This document has been published to replace these parts with " !
CONTENTS
[1] INTEGRATED CIRCUITS...
Service Manual - Page 109
Washer (Not Replacement Item )
BK
Changer Mechanism Unit
AC
Bracket, PWB Support
AB
Screw, Special
AB
Screw,... M3 X8mm
AA
Screw, M3 X10mm
XL-UH250
14 Front Panel
AM
Panel, FL Display
AD
Badge, SHARP
AE
Button, Function, A
AE
Button, Disc No.
PARTS CODE
[11] CABINET PARTS
201 CCABA6656AW01
201-1
201-3 HDECQA328AWSA
201-4... (LG2-5)
AC
Label, Specification
----
Service Manual - Page 116
No part of the publisher. SHARP CORPORATION Sharp-Roxy Corporation Sungai Petani, Kedah, Malaysia
Printed in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of this publication may be reproduced, stored in a retrieval system, or transmitted in Malaysia
A0702-1MX•RR•M SC
21
XL-UH250
COPYRIGHT...
Sharp XL-UH250 Reviews
Do you have an experience with the Sharp XL-UH250 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Sharp yet.
Earn 750 points for your review!