XE-A203 Operation Manual in English and Spanish
Page 5
...Register Number and Consecutive Number Programming 44 2 Electronic Journal (EJ) Programming ...45 3 Various Function Selection Programming 1 47 Function selection for miscellaneous keys 47 Print format ...48 Receipt print...Programming 2 51 Power save mode ...51 Logo message print format ...51 Online time out setting ...52 Thermal printer density ...52 Language selection...53 ...Error ...68 3 Cautions in Handling the Printer and Recording Paper 68 4 Replacing the Batteries...69 5 Replacing the Paper Roll ...69 6 Removing a Paper Jam ...72 7 Cleaning the Printer (Print Head...
...Register Number and Consecutive Number Programming 44 2 Electronic Journal (EJ) Programming ...45 3 Various Function Selection Programming 1 47 Function selection for miscellaneous keys 47 Print format ...48 Receipt print...Programming 2 51 Power save mode ...51 Logo message print format ...51 Online time out setting ...52 Thermal printer density ...52 Language selection...53 ...Error ...68 3 Cautions in Handling the Printer and Recording Paper 68 4 Replacing the Batteries...69 5 Replacing the Paper Roll ...69 6 Removing a Paper Jam ...72 7 Cleaning the Printer (Print Head...
XE-A203 Operation Manual in English and Spanish
Page 70
...the register prints "========" and then carries out the correct printing procedure after power recovery. (See the sample print.) 2 In Case of Printer Error If the printer runs out of the display. Key l entries will appear on the paper can discolor under conditions of the print head and print roller...copied blueprint, and heat caused by SHARP. • Do not unpack the thermal paper until it . • Avoid heat. The paper will print the power failure symbol and resume printing. Key entries l will print the power failure symbol and resume printing. 3 Cautions in Handling the Printer...
...the register prints "========" and then carries out the correct printing procedure after power recovery. (See the sample print.) 2 In Case of Printer Error If the printer runs out of the display. Key l entries will appear on the paper can discolor under conditions of the print head and print roller...copied blueprint, and heat caused by SHARP. • Do not unpack the thermal paper until it . • Avoid heat. The paper will print the power failure symbol and resume printing. Key entries l will print the power failure symbol and resume printing. 3 Cautions in Handling the Printer...
XE-A203 Operation Manual in English and Spanish
Page 75
...depression of the key for direct finalization Compulsory tendering No entry of a clerk code Overflow limitation error The open price entry. Make a clerk code entry. Make a registration within 25 steps....plug out or loosely connected to the electrical outlet? • Is a clerk code assigned to the register? • Is the mode switch set properly at the "REG" position? • Is the...paper is taken up spool.) • Is the print roller arm securely locked? • Is the paper roll properly installed? • Are the print head/sensor/roller clean? a Memory is full (in the...
...depression of the key for direct finalization Compulsory tendering No entry of a clerk code Overflow limitation error The open price entry. Make a clerk code entry. Make a registration within 25 steps....plug out or loosely connected to the electrical outlet? • Is a clerk code assigned to the register? • Is the mode switch set properly at the "REG" position? • Is the...paper is taken up spool.) • Is the print roller arm securely locked? • Is the paper roll properly installed? • Are the print head/sensor/roller clean? a Memory is full (in the...
Service Manual
Page 5
... • Dot pitch : Horizontal Vertical 0.167mm 0.174mm • Font : 10 dots (W) x 24 dots (H) • Printing capacity : max. 24 characters • Character size : 1.67mm (W) x 4.17mm (H) at the timing of thermal head heater elements 288 dots (4.75) 48 (288 dots) print area (max.24 characters) (4.75) 0.167 XE-A203U/XE-A203A SPECIFICATIONS - 3 - 57.5±0.5 (Paper dimension) (units : mm)
... • Dot pitch : Horizontal Vertical 0.167mm 0.174mm • Font : 10 dots (W) x 24 dots (H) • Printing capacity : max. 24 characters • Character size : 1.67mm (W) x 4.17mm (H) at the timing of thermal head heater elements 288 dots (4.75) 48 (288 dots) print area (max.24 characters) (4.75) 0.167 XE-A203U/XE-A203A SPECIFICATIONS - 3 - 57.5±0.5 (Paper dimension) (units : mm)
Service Manual
Page 14
... each model (omissible) 2 Test procedure The keyboard is checked with the sum check data of paper 0: Head up sensor 1: Head down 4 End of testing 0: Out of the key code except for the paper feed key. If not, an error print is inputted to the upper 4 digits of testing When any key and the printer... clock counts up normally. 5 End of the diag code, and the data is compared with each model is made. (*) The final key: "CA/AT" Key (*) XE-A203U/A203A sum check code: 3417 3 Display OP display: 104 POPUP display: 4 End of testing When the test ends normally: 104 When an...
... each model (omissible) 2 Test procedure The keyboard is checked with the sum check data of paper 0: Head up sensor 1: Head down 4 End of testing 0: Out of the key code except for the paper feed key. If not, an error print is inputted to the upper 4 digits of testing When any key and the printer... clock counts up normally. 5 End of the diag code, and the data is compared with each model is made. (*) The final key: "CA/AT" Key (*) XE-A203U/A203A sum check code: 3417 3 Display OP display: 104 POPUP display: 4 End of testing When the test ends normally: 104 When an...
Service Manual
Page 16
...in status (key input, change in RS port). 3 Display OP display: . End print: HEAD TEMP HEAD VOLTAGE BATTERY VOLTAGE 160 *** *** *** 15) SLEEP MODE TEST 1 Key operation 550 RCPT/PO 2 Test procedure Check to the error print.) XE-A203U/XE-A203A TEST FUNCTION - 14 - VENDOR ID PRODUCT ID DEVICE ADDRESS 520 XXX XXX ... test When any key is pressed, the test is terminated and the AD value at the terminating point is printed. POPUP display: 4 End of the test, the SD card register value is displayed. After completion of the test The test will automatically be terminated and the printer...
...in status (key input, change in RS port). 3 Display OP display: . End print: HEAD TEMP HEAD VOLTAGE BATTERY VOLTAGE 160 *** *** *** 15) SLEEP MODE TEST 1 Key operation 550 RCPT/PO 2 Test procedure Check to the error print.) XE-A203U/XE-A203A TEST FUNCTION - 14 - VENDOR ID PRODUCT ID DEVICE ADDRESS 520 XXX XXX ... test When any key is pressed, the test is terminated and the AD value at the terminating point is printed. POPUP display: 4 End of the test, the SD card register value is displayed. After completion of the test The test will automatically be terminated and the printer...