Service Manual
Page 8
TV (Rear/Top) HDMI terminal (INPUT 4) HDMI terminal (INPUT 5) PC IN terminals (INPUT 6) Antenna/Cable in AUDIO terminals (INPUT 5) DIGITAL AUDIO OUTPUT terminal INPUT 3 terminals Remote control sensor OPC sensor* OPC indicator** SLEEP indicator** POWER indicator** Channel buttons (CH / ) Volume buttons (VOL / ) INPUT button POWER button INPUT 1 terminals INPUT 2 terminals AUDIO OUTPUT terminals AC INPUT terminal 1 - 2 LC-52D43U [2] OPERATION MANUAL Part names TV (Front) NOTE *OPC: Optical Picture Control. **TV status indicator.
TV (Rear/Top) HDMI terminal (INPUT 4) HDMI terminal (INPUT 5) PC IN terminals (INPUT 6) Antenna/Cable in AUDIO terminals (INPUT 5) DIGITAL AUDIO OUTPUT terminal INPUT 3 terminals Remote control sensor OPC sensor* OPC indicator** SLEEP indicator** POWER indicator** Channel buttons (CH / ) Volume buttons (VOL / ) INPUT button POWER button INPUT 1 terminals INPUT 2 terminals AUDIO OUTPUT terminals AC INPUT terminal 1 - 2 LC-52D43U [2] OPERATION MANUAL Part names TV (Front) NOTE *OPC: Optical Picture Control. **TV status indicator.
Service Manual
Page 9
... operational buttons: Operate the external equipment. 5 0 - 9: Set the channel. 6 • (DOT): 7 INPUT: Select a TV input source. (TV, INPUT 1, INPUT 2, INPUT 3, INPUT 4, INPUT 5, INPUT 6) 8 VOL / : Set the volume. 9 SURROUND: Select Surround settings. 10 FREEZE: Set the still image. LC-52D43U Part names Remote control unit 1 14 2 3 15 4 16 5 6 17 7 18 8 19 9 20 10 21 22 11 23...
... operational buttons: Operate the external equipment. 5 0 - 9: Set the channel. 6 • (DOT): 7 INPUT: Select a TV input source. (TV, INPUT 1, INPUT 2, INPUT 3, INPUT 4, INPUT 5, INPUT 6) 8 VOL / : Set the volume. 9 SURROUND: Select Surround settings. 10 FREEZE: Set the still image. LC-52D43U Part names Remote control unit 1 14 2 3 15 4 16 5 6 17 7 18 8 19 9 20 10 21 22 11 23...
Service Manual
Page 11
the AC cord and replugging it to the TV setting position. • Are batteries inserted with polarity ( , ) aligned? • Are batteries worn out? (Replace with new batteries.) LC-52D43U • Picture is cut off . • Is the sleep timer set correctly? Set it in after connection? ...broadcast. • No broadcast now. Also, do not leave the unit in "Output Select"? • Have you pressed TV POWER on the remote control unit? • The TV sometimes makes a cracking sound. • This is correctly setup. • Check the broadcast time in high and low temperature...
the AC cord and replugging it to the TV setting position. • Are batteries inserted with polarity ( , ) aligned? • Are batteries worn out? (Replace with new batteries.) LC-52D43U • Picture is cut off . • Is the sleep timer set correctly? Set it in after connection? ...broadcast. • No broadcast now. Also, do not leave the unit in "Output Select"? • Have you pressed TV POWER on the remote control unit? • The TV sometimes makes a cracking sound. • This is correctly setup. • Check the broadcast time in high and low temperature...
Service Manual
Page 20
LC-52D43U LCC5H2DA43PU TER 3. AV MODE: [DYNAMIC] Backlight: +16 Aging time: Min. 60 minutes 2) Connect the white balance adjustment tool to the set . Multi-point adjustment mode 5) ...] ment execution Process mode 1) Using the remote controller, transmit the "monitor adjustment process" code. If a value should become improper or an adjustment is made to the optimum conditions at each point.) (WBI50800) [Adjustment value] MG5G**** MG5B**** • As per the "standard set" submitted by Engineering Department "LC-52D43U" Teaching set at 920 * Initial R, G and...
LC-52D43U LCC5H2DA43PU TER 3. AV MODE: [DYNAMIC] Backlight: +16 Aging time: Min. 60 minutes 2) Connect the white balance adjustment tool to the set . Multi-point adjustment mode 5) ...] ment execution Process mode 1) Using the remote controller, transmit the "monitor adjustment process" code. If a value should become improper or an adjustment is made to the optimum conditions at each point.) (WBI50800) [Adjustment value] MG5G**** MG5B**** • As per the "standard set" submitted by Engineering Department "LC-52D43U" Teaching set at 920 * Initial R, G and...