User Guide
Page 6
CHARGING Note: Charge for 3 hours before first use. 1. Lift and position earpieces inside headband so foam ear cushions face each other. 3. Connect AC charger to desktop charging stand and universal adapter. 2. Headset indicator light flashes when charging. 5 Place headset into desktop charging stand.
CHARGING Note: Charge for 3 hours before first use. 1. Lift and position earpieces inside headband so foam ear cushions face each other. 3. Connect AC charger to desktop charging stand and universal adapter. 2. Headset indicator light flashes when charging. 5 Place headset into desktop charging stand.
User Guide
Page 8
... call control button. 3. Use the phone menu to search for passkey, enter 0000. For set up and pairing instructions with headset turned off. When prompted for Bluetooth devices and select "590 Plantronics." 4. PAIRING Pairing with Bluetooth® Device 1 2 Begin with Bluetooth devices other than mobile phones, please consult your Bluetooth device user...
... call control button. 3. Use the phone menu to search for passkey, enter 0000. For set up and pairing instructions with headset turned off. When prompted for Bluetooth devices and select "590 Plantronics." 4. PAIRING Pairing with Bluetooth® Device 1 2 Begin with Bluetooth devices other than mobile phones, please consult your Bluetooth device user...
User Guide
Page 9
... flashing red and blue, release the button. To reconnect, press the adapter pairing/connect button. Power headset on . 4. Headset and adapter will flash blue when paired successfully. 8 Press and hold the adapter pairing/ connect button for 7-10 seconds.... red and blue: 1. To pair again, follow directions below. 1 2 Begin with the universal adapter at the factory. If adapter and headset continue to flash red rather than blue, connect or pair them again. PAIRING Pairing Headset with Universal Adapter NOTE: The Pulsar 590A headset is paired with headset turned off.
... flashing red and blue, release the button. To reconnect, press the adapter pairing/connect button. Power headset on . 4. Headset and adapter will flash blue when paired successfully. 8 Press and hold the adapter pairing/ connect button for 7-10 seconds.... red and blue: 1. To pair again, follow directions below. 1 2 Begin with the universal adapter at the factory. If adapter and headset continue to flash red rather than blue, connect or pair them again. PAIRING Pairing Headset with Universal Adapter NOTE: The Pulsar 590A headset is paired with headset turned off.
User Guide
Page 10
Point tip of telescoping voice tube toward mouth and extend for optimal voice transmission - Adjust headband if necessary. may require two hands. 9 ADJUSTING FIT Position headset so that telescoping voice tube is on right ear.
Point tip of telescoping voice tube toward mouth and extend for optimal voice transmission - Adjust headband if necessary. may require two hands. 9 ADJUSTING FIT Position headset so that telescoping voice tube is on right ear.
User Guide
Page 11
IN-FLIGHT AND WIRED USES In-flight cable can be used with any 3.5mm audio jack to the in-flight cable, not the headset. 10 Insert in-flight cable into wired headphones. To control volume, use . Power headset off. 2. Note: Telescoping voice tube and all headset controls are disabled when in use the device connected to convert your wireless headset into 3.5mm jack on . 1. Headset will not operate when in-flight cable is connected and headset is in -flight cable is powered on left earpiece.
IN-FLIGHT AND WIRED USES In-flight cable can be used with any 3.5mm audio jack to the in-flight cable, not the headset. 10 Insert in-flight cable into wired headphones. To control volume, use . Power headset off. 2. Note: Telescoping voice tube and all headset controls are disabled when in use the device connected to convert your wireless headset into 3.5mm jack on . 1. Headset will not operate when in-flight cable is connected and headset is in -flight cable is powered on left earpiece.