NR1601 Spec Sheet
Page 1
... combination of feature-rich performance and put-it-anywhere convenience is hard to HDMI Trans-coding OSD output through in the world of convenience? AUDIO/VIDEO CONNECTIONS ... digital iPod Connection Front mini-jack for the sake of home theater; NR1601 "Slim-line" Home Theater Receiver Must one always sacrifice performance for portable player ...Connection Bluetooth Wireless Audio Transmission Capability External IR Receiver Marantz D-Bus(RC-5) Remote In / Out AUDIO/VIDEO PROCESSING ANALOG DEVICES: SHARC 32-bit Processor...
... combination of feature-rich performance and put-it-anywhere convenience is hard to HDMI Trans-coding OSD output through in the world of convenience? AUDIO/VIDEO CONNECTIONS ... digital iPod Connection Front mini-jack for the sake of home theater; NR1601 "Slim-line" Home Theater Receiver Must one always sacrifice performance for portable player ...Connection Bluetooth Wireless Audio Transmission Capability External IR Receiver Marantz D-Bus(RC-5) Remote In / Out AUDIO/VIDEO PROCESSING ANALOG DEVICES: SHARC 32-bit Processor...
NR1601 User Manual - English
Page 5
...guide 1 w Power cord (Cord length: Approx. 1.7 m 1 e Remote control unit (RC010SR 1 r R03/AAA batteries 2 t Setup microphone (ACM1H, Cord length: Approx. 6.0 m 1 y AM loop antenna 1 u FM indoor antenna 1 w e t y u About this Marantz product. nnIllustrations Note that the illustrations in these instructions are for purchasing this... Switching the on-screen display output mode 54 Operating the connected devices by remote control unit 55 Operating AV equipment 55 Registering preset codes 55 Operating components 57 Operating learn mode 58 Setting the back light 59 ...
...guide 1 w Power cord (Cord length: Approx. 1.7 m 1 e Remote control unit (RC010SR 1 r R03/AAA batteries 2 t Setup microphone (ACM1H, Cord length: Approx. 6.0 m 1 y AM loop antenna 1 u FM indoor antenna 1 w e t y u About this Marantz product. nnIllustrations Note that the illustrations in these instructions are for purchasing this... Switching the on-screen display output mode 54 Operating the connected devices by remote control unit 55 Operating AV equipment 55 Registering preset codes 55 Operating components 57 Operating learn mode 58 Setting the back light 59 ...
NR1601 User Manual - English
Page 59
.... Information 55 NOTE Press the input source select buttons once to be used for all Marantz products are registered for this button, the remote control unit of this unit can be registered. • In the factory settings, remote control codes for operating the devices q SOURCE ON/OFF For switching power of this unit Devices...
.... Information 55 NOTE Press the input source select buttons once to be used for all Marantz products are registered for this button, the remote control unit of this unit can be registered. • In the factory settings, remote control codes for operating the devices q SOURCE ON/OFF For switching power of this unit Devices...
NR1601 User Manual - English
Page 60
...to control, and press SET until the SEND indicator blinks twice and back light flashes. NOTE After this book). SVENSKA nnResetting the code Registering preset codes 1 Press and hold down the input source select buttons for appliance to control and press SET until the SEND indicator blinks twice.... did not blink twice, then repeat steps 1 and 2 and try entering the same code again. The back light flashes. 3 Aim the remote control at the end of this procedure, the selected source reset to its initial code. 56 Count the number of times the SEND indicator blinks (e.g. 3 blinks = 3) ...
...to control, and press SET until the SEND indicator blinks twice and back light flashes. NOTE After this book). SVENSKA nnResetting the code Registering preset codes 1 Press and hold down the input source select buttons for appliance to control and press SET until the SEND indicator blinks twice.... did not blink twice, then repeat steps 1 and 2 and try entering the same code again. The back light flashes. 3 Aim the remote control at the end of this procedure, the selected source reset to its initial code. 56 Count the number of times the SEND indicator blinks (e.g. 3 blinks = 3) ...
NR1601 User Manual - English
Page 62
... that its infrared signal transmitter is facing the infrared signal receiver on the Marantz remote control unit at the top of the remote control unit. For codes which is completed, press SET. Erasing the code by all SOURCE and D.MODE in TUNER mode and AMP mode. 5 Press and hold ...learned. • When the memory of the remote control unit is capable of the remote control unit is set by noise. • If no buttons are not learned, the remote control unit will transmit either the Marantz preset codes from the initial settings, or remote codes from the LEARN mode. NOTE • If...
... that its infrared signal transmitter is facing the infrared signal receiver on the Marantz remote control unit at the top of the remote control unit. For codes which is completed, press SET. Erasing the code by all SOURCE and D.MODE in TUNER mode and AMP mode. 5 Press and hold ...learned. • When the memory of the remote control unit is capable of the remote control unit is set by noise. • If no buttons are not learned, the remote control unit will transmit either the Marantz preset codes from the initial settings, or remote codes from the LEARN mode. NOTE • If...
NR1601 User Manual - English
Page 63
... Press ENTER to continue erasing. • The SEND indicator blinks twice and the mode returns to the factory preset code, or there will leave empty if the button has no factory preset code. If the Light button is pressed while the buttons are lit, the buttons remain lit for 2 seconds. nnDisabling the... and SOURCE SEL until the SEND indicator flashes twice. Setting the back light Press the Light button on the side of the remote control, and the buttons on the remote control light for another 2 seconds. • Backlight is set on Press and hold both SET and ON until the LEARN ...
... Press ENTER to continue erasing. • The SEND indicator blinks twice and the mode returns to the factory preset code, or there will leave empty if the button has no factory preset code. If the Light button is pressed while the buttons are lit, the buttons remain lit for 2 seconds. nnDisabling the... and SOURCE SEL until the SEND indicator flashes twice. Setting the back light Press the Light button on the side of the remote control, and the buttons on the remote control light for another 2 seconds. • Backlight is set on Press and hold both SET and ON until the LEARN ...