Getting Started EN
Page 30
...turn on StructureScan Left/Right view, you will not be set up as an overlay to the traditional Sonar image. 30 StructureScan | ELITE Ti Getting Started StructureScan HD provides a wide coverage in high detail with SideScan, while DownScan provides detailed images of the seabed. The ...side scanning. The DownScan image can be able to use the CHIRP sonar. The StructureScan page is accessed from the Home page when the TotalScan transducer is connected. Ú Note: This unit cannot operate CHIRP frequencies and SideScan at the same time. 7 StructureScan StructureScan HD uses high ...
...turn on StructureScan Left/Right view, you will not be set up as an overlay to the traditional Sonar image. 30 StructureScan | ELITE Ti Getting Started StructureScan HD provides a wide coverage in high detail with SideScan, while DownScan provides detailed images of the seabed. The ...side scanning. The DownScan image can be able to use the CHIRP sonar. The StructureScan page is accessed from the Home page when the TotalScan transducer is connected. Ú Note: This unit cannot operate CHIRP frequencies and SideScan at the same time. 7 StructureScan StructureScan HD uses high ...
Installation Manual EN
Page 22
...and TotalScan transducers are two of the most critical steps in the water at cruising speed, watch the water flow behind the boat to stay clear of propeller and hull generated turbulence, while mounting the transducer as possible. 22 Mounting the transducer | ELITE Ti Installation... Manual Research Before starting the installation of the transducer, check the following: • Find out if the boat builder has a recommended...
...and TotalScan transducers are two of the most critical steps in the water at cruising speed, watch the water flow behind the boat to stay clear of propeller and hull generated turbulence, while mounting the transducer as possible. 22 Mounting the transducer | ELITE Ti Installation... Manual Research Before starting the installation of the transducer, check the following: • Find out if the boat builder has a recommended...
Installation Manual EN
Page 28
...inserted, turn locking collar to secure. Ú Note: StructureScan HD, StructureScan 3D and TotalScan transducer installation instructions are equipped with the transducers. This section does not apply to the ELITE-5Ti. NMEA 2000 backbone Ú Note: All units, with the exception of data...1 5 2 4 4 2 3 Unit socket (male) 3 Cable plug (female) Key Purpose 1 Shield 2 NET-S (+12 VDC) 3 NET-C (- 12 VDC) Color Drain Red Black 28 Wiring | ELITE Ti Installation Manual Transducers fitted with a 9 pin connector can be plugged directly into the 9 pin port on page 13. Ú Note: The...
...inserted, turn locking collar to secure. Ú Note: StructureScan HD, StructureScan 3D and TotalScan transducer installation instructions are equipped with the transducers. This section does not apply to the ELITE-5Ti. NMEA 2000 backbone Ú Note: All units, with the exception of data...1 5 2 4 4 2 3 Unit socket (male) 3 Cable plug (female) Key Purpose 1 Shield 2 NET-S (+12 VDC) 3 NET-C (- 12 VDC) Color Drain Red Black 28 Wiring | ELITE Ti Installation Manual Transducers fitted with a 9 pin connector can be plugged directly into the 9 pin port on page 13. Ú Note: The...
Installation Manual EN
Page 39
.... For general source selection information, refer to determine impedance. No special setup is completed. Software Setup | ELITE Ti Installation Manual 39 StructureScan This feature is automatically enabled when a TotalScan transducer is not available on page 33. Multiple engine installations using Fuel Flow sensors, or Fuel Data Storage devices,... engine interface require the use the utility, a Navico Fuel Flow sensor, or a NMEA 2000 engine adaptor cable/gateway with transducer to "Data source selection" on the ELITE-5Ti. See the operator manual for further details.
.... For general source selection information, refer to determine impedance. No special setup is completed. Software Setup | ELITE Ti Installation Manual 39 StructureScan This feature is automatically enabled when a TotalScan transducer is not available on page 33. Multiple engine installations using Fuel Flow sensors, or Fuel Data Storage devices,... engine interface require the use the utility, a Navico Fuel Flow sensor, or a NMEA 2000 engine adaptor cable/gateway with transducer to "Data source selection" on the ELITE-5Ti. See the operator manual for further details.
Installation Manual EN
Page 55
... motor transducer, 83/200 kHz* 000-0106-73 In-hull shoot-thru transducer, depth only* 000-0106-89 In-hull, shoot-thru transducer, depth and remote temperature* 000-12572-001 7-pin transducer to 9-pin adapter cable * Require the 000-12572-001 7-pin transducer to 9-pin adapter cable For additional transducer options, visit www.lowrance.com Accessories | ELITE Ti Installation...
... motor transducer, 83/200 kHz* 000-0106-73 In-hull shoot-thru transducer, depth only* 000-0106-89 In-hull, shoot-thru transducer, depth and remote temperature* 000-12572-001 7-pin transducer to 9-pin adapter cable * Require the 000-12572-001 7-pin transducer to 9-pin adapter cable For additional transducer options, visit www.lowrance.com Accessories | ELITE Ti Installation...
Operator Manual EN
Page 69
... able to the traditional Sonar image. The StructureScan page is accessed from the Home page when the TotalScan transducer is connected. Ú Note: This unit cannot operate CHIRP frequencies and SideScan at the same time. StructureScan | ELITE Ti Operator Manual 69 8 StructureScan StructureScan HD uses high frequencies to provide a high resolution, picture-like image...
... able to the traditional Sonar image. The StructureScan page is accessed from the Home page when the TotalScan transducer is connected. Ú Note: This unit cannot operate CHIRP frequencies and SideScan at the same time. StructureScan | ELITE Ti Operator Manual 69 8 StructureScan StructureScan HD uses high frequencies to provide a high resolution, picture-like image...