Service Manual
Page 4
...before removing the protective material from a carpeted floor can generate electrical charges sufficient to the receiver chassis ground before connecting the test receiver positive lead. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will be soldered..., and hold the soldering iron tip and solder the strand against the component lead until the solder melts. b. Always connect the test receiver ground lead to damage ES devices. 5. a. Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can generate electrical...
...before removing the protective material from a carpeted floor can generate electrical charges sufficient to the receiver chassis ground before connecting the test receiver positive lead. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will be soldered..., and hold the soldering iron tip and solder the strand against the component lead until the solder melts. b. Always connect the test receiver ground lead to damage ES devices. 5. a. Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can generate electrical...
Service Manual
Page 6
... is followed a special standard. 3.General Specification(TV) No Item 1. RF Input Channel 4. SPECIFICATION NOTE : Specifications and others are subject to ML-051A chassis. 2. Requirement for Test Testing for standard of each part must be followed in below condition. (1) Temperature: 25°C ± 2°C (2) Humidity: 65% ± 10% (3) Power: Standard input voltage (AC...
... is followed a special standard. 3.General Specification(TV) No Item 1. RF Input Channel 4. SPECIFICATION NOTE : Specifications and others are subject to ML-051A chassis. 2. Requirement for Test Testing for standard of each part must be followed in below condition. (1) Temperature: 25°C ± 2°C (2) Humidity: 65% ± 10% (3) Power: Standard input voltage (AC...
Service Manual
Page 11
...Specification. 2.1 Because this is not a hot chassis, it is not necessary to protect test instruments. 2.2 Adjustment must be done in the correct sequence. 2.3 The adjustment must be... use an isolation transformer. Never connect HDMI & DVI-D & DVI-A Cable at LG TV Plant 2. Application Range This spec. Checksum: ChangeCable by total EDID data -...* Caution - Model Name(Hex) : Model Name Model Name(HEX) 26LX2R-ZE 32364C5832522D5A45 32LX2R-ZE 33324C5832522D5A45 32LP1R-ZE 33324C5031522D5A45 37LP1R-ZE 33374C5031522D5A45 42LP1R-ZE 34324C5031522D5A45 e. Use the proper signal...
...Specification. 2.1 Because this is not a hot chassis, it is not necessary to protect test instruments. 2.2 Adjustment must be done in the correct sequence. 2.3 The adjustment must be... use an isolation transformer. Never connect HDMI & DVI-D & DVI-A Cable at LG TV Plant 2. Application Range This spec. Checksum: ChangeCable by total EDID data -...* Caution - Model Name(Hex) : Model Name Model Name(HEX) 26LX2R-ZE 32364C5832522D5A45 32LX2R-ZE 33324C5832522D5A45 32LP1R-ZE 33324C5031522D5A45 37LP1R-ZE 33374C5031522D5A45 42LP1R-ZE 34324C5031522D5A45 e. Use the proper signal...
Service Manual
Page 12
.... 4) Press the (Vol. +) key to operate the set , then it becomes automatically. 5) Auto-RGB OK means the adjustment is completed. 4.3 Adjustment of RF/AV/SAV * Test Equipment - Remote controller for adjustment - white Balance 4.1 Adjustment of RGB * Required Equipments - 4. ADC Calibration 5. Remote controller for White Balance mode 5) Adjust High light with R/B Gain...
.... 4) Press the (Vol. +) key to operate the set , then it becomes automatically. 5) Auto-RGB OK means the adjustment is completed. 4.3 Adjustment of RF/AV/SAV * Test Equipment - Remote controller for adjustment - white Balance 4.1 Adjustment of RGB * Required Equipments - 4. ADC Calibration 5. Remote controller for White Balance mode 5) Adjust High light with R/B Gain...