PRESCRIBE Commands Technical Reference Manual - Rev. 4.7
Page 105
... language B7 selection at power-on 0: Automatically enters message language 1 selection menu at power-on . non-engine-dependent Host buffer size H0 0 to 99 in units of 10MB (0 to 990MB) 0 Serial interface baud H1 rate 3: 300 bps (not valid for some models) 12: 1200 bps 24: 2400 bps 48: 4800 bps...3: XON/XOFF 6-5 Error is set automatically. 1: Does not automatically enter message language selection menu at the initial power-on . Interface-independent Parameters (Sheet 1 of page 0 1: Fuser sensor activated 2: Fuser sensor deactivated 3: Page ejection 4: Same as 0;
... language B7 selection at power-on 0: Automatically enters message language 1 selection menu at power-on . non-engine-dependent Host buffer size H0 0 to 99 in units of 10MB (0 to 990MB) 0 Serial interface baud H1 rate 3: 300 bps (not valid for some models) 12: 1200 bps 24: 2400 bps 48: 4800 bps...3: XON/XOFF 6-5 Error is set automatically. 1: Does not automatically enter message language selection menu at the initial power-on . Interface-independent Parameters (Sheet 1 of page 0 1: Fuser sensor activated 2: Fuser sensor deactivated 3: Page ejection 4: Same as 0;
FS-1370DN Operation Guide (Basic)
Page 83
... pinched by holding the green levers with both hands. Never expose the drum unit to light for more than five minutes. 4 If the jammed paper appears to step 2. 2 Open the top cover and front cover, and lift the developer unit together with the toner container out of the printer. 3 Remove the drum... the printer by rollers, pull it may result in burn injury. Remove any partially fed paper. CAUTION The fuser unit inside the printer is sensitive to remove paper that has already been partially fed. Note The drum is hot. Troubleshooting 5-15 Do not touch it, ...
... pinched by holding the green levers with both hands. Never expose the drum unit to light for more than five minutes. 4 If the jammed paper appears to step 2. 2 Open the top cover and front cover, and lift the developer unit together with the toner container out of the printer. 3 Remove the drum... the printer by rollers, pull it may result in burn injury. Remove any partially fed paper. CAUTION The fuser unit inside the printer is sensitive to remove paper that has already been partially fed. Note The drum is hot. Troubleshooting 5-15 Do not touch it, ...
FS-1370DN Operation Guide (Basic)
Page 85
If the paper is hot. Troubleshooting 5-17 Do not touch it, as it out. 2 Close the rear cover, and open the fuser cover and remove the paper by pulling it out. The printer warms up and resumes printing. CAUTION The fuser unit inside the printer is jammed inside the fuser unit, open and close the top cover to clear the error. Rear Cover 1 Open the rear cover and remove the jammed paper by pulling it may result in burn injury.
If the paper is hot. Troubleshooting 5-17 Do not touch it, as it out. 2 Close the rear cover, and open the fuser cover and remove the paper by pulling it out. The printer warms up and resumes printing. CAUTION The fuser unit inside the printer is jammed inside the fuser unit, open and close the top cover to clear the error. Rear Cover 1 Open the rear cover and remove the jammed paper by pulling it may result in burn injury.
FS-1370DN Operation Guide (Basic)
Page 91
... jams 5-14 E Environmental standard requirements 6-4 Error messages of memory card 5-8 of RAM disk 5-8 tabled, with corrective actions 5-5 Express mode installation method 3-14 F Front cover components 1-2 Fuser unit clearing paper jams 5-17 G General problems troubleshooting 5-2 I Inside the printer clearing paper jams 5-15 Installation method custom mode 3-15 express mode 3-14 Installation precautions xvi...
... jams 5-14 E Environmental standard requirements 6-4 Error messages of memory card 5-8 of RAM disk 5-8 tabled, with corrective actions 5-5 Express mode installation method 3-14 F Front cover components 1-2 Fuser unit clearing paper jams 5-17 G General problems troubleshooting 5-2 I Inside the printer clearing paper jams 5-15 Installation method custom mode 3-15 express mode 3-14 Installation precautions xvi...