FS-1020D Operation Guide Rev 1.4
Page 22
... normal office lighting (500 lux) for more than five minutes. The drum in the following manner. 1 Open the printer's top and front covers. Note Figure 2-9 2-6 Process Unit Cleaning the Printer 2.2 Cleaning the Printer To avoid print quality problems, the interior of the printer must be done from time to time to avoid print quality problems...
... normal office lighting (500 lux) for more than five minutes. The drum in the following manner. 1 Open the printer's top and front covers. Note Figure 2-9 2-6 Process Unit Cleaning the Printer 2.2 Cleaning the Printer To avoid print quality problems, the interior of the printer must be done from time to time to avoid print quality problems...
FS-1020D Operation Guide Rev 1.4
Page 54
...) 0.115 to 0.145 mm (4.5 to 5.7 mils) 4 to 6% (composite) 4-8 The adhesive layer consists of its top sheet, with an extra margin of the printer. Do not remove the extra top sheet from the carrier sheet until use. The carrier sheet (also called the linear or backing sheet) holds the...is printed on page 4-8. Due to peel off, causing serious paper jam problems. Some label paper is particularly likely to the drum or rollers will damage the printer. Figure 4-1 Top sheet (white bond paper) Adhesive Carrier sheet Adhesive label paper must be entirely covered by its composition, ...
...) 0.115 to 0.145 mm (4.5 to 5.7 mils) 4 to 6% (composite) 4-8 The adhesive layer consists of its top sheet, with an extra margin of the printer. Do not remove the extra top sheet from the carrier sheet until use. The carrier sheet (also called the linear or backing sheet) holds the...is printed on page 4-8. Due to peel off, causing serious paper jam problems. Some label paper is particularly likely to the drum or rollers will damage the printer. Figure 4-1 Top sheet (white bond paper) Adhesive Carrier sheet Adhesive label paper must be entirely covered by its composition, ...
FS-1020D Operation Guide Rev 1.4
Page 89
...Printer Specifications Item Printing method Printing speed Resolution First print Warm-up time Controller Main memory Self test Maximum duty cycle Drum Developer Main charger Transferring Separation Drum cleaning Drum discharging Fuser Toner saving Paper Waste toner capacity Paper feed trays Capacity of output trays Table C-1 Description Electrophotography, laser...of the same page Fast 1200 mode 600 dpi (vertical and horizontal) with KIR (Kyocera Image Refinement) 300 dpi (vertical and horizontal) with KIR (Kyocera Image Refinement) Approx. 10 seconds or less (A4 or letter size), depends on ...
...Printer Specifications Item Printing method Printing speed Resolution First print Warm-up time Controller Main memory Self test Maximum duty cycle Drum Developer Main charger Transferring Separation Drum cleaning Drum discharging Fuser Toner saving Paper Waste toner capacity Paper feed trays Capacity of output trays Table C-1 Description Electrophotography, laser...of the same page Fast 1200 mode 600 dpi (vertical and horizontal) with KIR (Kyocera Image Refinement) 300 dpi (vertical and horizontal) with KIR (Kyocera Image Refinement) Approx. 10 seconds or less (A4 or letter size), depends on ...
FS-1020D Operation Guide Rev 1.4
Page 93
... disk drive that use them, refer to indicate the printer's status. Glossary MP tray This is the printer's main module and contains the photosensitive drum and developer unit. Offline The printer can perform IEEE1284 compatible bi-directional communications. The MP tray is the Kyocera Mita page printer control language installed on the CDROM supplied with the...
... disk drive that use them, refer to indicate the printer's status. Glossary MP tray This is the printer's main module and contains the photosensitive drum and developer unit. Offline The printer can perform IEEE1284 compatible bi-directional communications. The MP tray is the Kyocera Mita page printer control language installed on the CDROM supplied with the...