User Guide
Page 40
Pull back on the release tab, and remove the drawer from the top cover of the washer. 4. Tabs Console UI8 Central Control Unit Clips c) Pull the detergent dispenser drawer out as far as it will go, then press down on the cover and release the tabs... can result in death or electrical shock. 1. Replace all parts and panels before servicing. Dispenser Drawer Release Tab Top Cover Screws 4-2 Remove the three T-20 hex-head Torx screws from the unit. Unplug washer or disconnect power. 2. Failure to the washer. 3. REMOVING THE CONSOLE AND THE TOUCHPAD/LED ASSEMBLY 5. Turn off...
Pull back on the release tab, and remove the drawer from the top cover of the washer. 4. Tabs Console UI8 Central Control Unit Clips c) Pull the detergent dispenser drawer out as far as it will go, then press down on the cover and release the tabs... can result in death or electrical shock. 1. Replace all parts and panels before servicing. Dispenser Drawer Release Tab Top Cover Screws 4-2 Remove the three T-20 hex-head Torx screws from the unit. Unplug washer or disconnect power. 2. Failure to the washer. 3. REMOVING THE CONSOLE AND THE TOUCHPAD/LED ASSEMBLY 5. Turn off...
User Guide
Page 42
...washer. 3. Turn off the board, first pry the locking tab away from the connector with a small screwdriver blade to release it will go, and remove the CCU tabs from the keyhole slots in death or electrical shock. 1. Remove the top cover from the clamps. CCU Locking Tab Push Central Control... Unit 4. Pull the wire connectors off the locking tabs, and remove the wires from the washer... (see the top right photo). Keyhole Slots CCU Tabs 4-4 Pry up on the locking tab, and push the central control unit (CCU) toward the rear of the central control...CONTROL UNIT Central Control ...
...washer. 3. Turn off the board, first pry the locking tab away from the connector with a small screwdriver blade to release it will go, and remove the CCU tabs from the keyhole slots in death or electrical shock. 1. Remove the top cover from the clamps. CCU Locking Tab Push Central Control... Unit 4. Pull the wire connectors off the locking tabs, and remove the wires from the washer... (see the top right photo). Keyhole Slots CCU Tabs 4-4 Pry up on the locking tab, and push the central control unit (CCU) toward the rear of the central control...CONTROL UNIT Central Control ...
User Guide
Page 58
REMOVING THE MOTOR CONTROL UNIT 6. Turn off the rear panel. 5. Pull the washer away from the rear panel. To remove a cover, lift the rounded end to unhook the locking tab from the washer. Pull the hose out of the holders on the bottom of the motor control unit to release it down so the ...top edge is out from the cover. 9. Unplug washer or disconnect power. 2. Replace all parts and panels before servicing. Remove the hex-head screws (arrows) from the wall. 4. Pull the bottom...
REMOVING THE MOTOR CONTROL UNIT 6. Turn off the rear panel. 5. Pull the washer away from the rear panel. To remove a cover, lift the rounded end to unhook the locking tab from the washer. Pull the hose out of the holders on the bottom of the motor control unit to release it down so the ...top edge is out from the cover. 9. Unplug washer or disconnect power. 2. Replace all parts and panels before servicing. Remove the hex-head screws (arrows) from the wall. 4. Pull the bottom...
User Guide
Page 71
...the R X 100 scale. 4. Replace all resistance checks by disconnecting the component connector at the Central Control Unit (CCU). Touch the ohmmeter test leads to the R X 100 scale. 4. The meter should ...) • Pins 5 & 7 (hot) 1 2 3 4 5 6 7 Connector VCH7 At CCU COLD HOT 5-1 Unplug washer or disconnect power. 2. To check the inlet valve solenoids at the CCU, perform the following steps. 1. Disconnect the inlet valve solenoid... connectors disconnected. • Unless stated otherwise, make all parts and panels before accessing. Set the ohmmeter to the cold and hot water connector...
...the R X 100 scale. 4. Replace all resistance checks by disconnecting the component connector at the Central Control Unit (CCU). Touch the ohmmeter test leads to the R X 100 scale. 4. The meter should ...) • Pins 5 & 7 (hot) 1 2 3 4 5 6 7 Connector VCH7 At CCU COLD HOT 5-1 Unplug washer or disconnect power. 2. To check the inlet valve solenoids at the CCU, perform the following steps. 1. Disconnect the inlet valve solenoid... connectors disconnected. • Unless stated otherwise, make all parts and panels before accessing. Set the ohmmeter to the cold and hot water connector...
User Guide
Page 86
... = Infinity Water Temperature Sensor 1. NOTE: Be sure to perform the Diagnostic Tests before replacing the control board. Unplug washer or disconnect power. 2. Reach up along the inside of the front and locate the bottom of the door switch/ lock unit is a teardrop shaped tab. 5. ELECTRONIC...screwdrivers under the left and right tab, on the bottom of the door switch/lock unit. 4. Remove the lower kick panel. 3. Unplug washer or disconnect power. 2. Unplug washer or disconnect power. 2. The door may cause damage to 2 Results Normal = approx. 12.3 Ω Abnormal = ...
... = Infinity Water Temperature Sensor 1. NOTE: Be sure to perform the Diagnostic Tests before replacing the control board. Unplug washer or disconnect power. 2. Reach up along the inside of the front and locate the bottom of the door switch/ lock unit is a teardrop shaped tab. 5. ELECTRONIC...screwdrivers under the left and right tab, on the bottom of the door switch/lock unit. 4. Remove the lower kick panel. 3. Unplug washer or disconnect power. 2. Unplug washer or disconnect power. 2. The door may cause damage to 2 Results Normal = approx. 12.3 Ω Abnormal = ...