IBM 86807RY - Netfinity 7000 M10 Support and Manuals
Popular IBM 86807RY Manual Pages
Hardware Maintenance Manual - Page 9
... System Security 28 Using the Power-On Password Menu . . . 29 Using the Administrator Password Menu . 31 Start Options 32 Advanced Setup 32 ACPI Control 32 Cache Control 33 PCI Slot/Device Information 33 Memory Settings 33 MPS Version Control 34 Error Logs 34 POST Error Log 34 System Error Log 34 Save Settings 34
© Copyright IBM Corp. 1998
1
Hardware Maintenance Manual - Page 12
... Network Adapters and Device Drivers 181 Symptom-to-FRU Index 182 Beep Symptoms 182 No Beep Symptoms 186 Diagnostic Error Codes 187 Error Symptoms 192 Power Control Card LED 194 Power Supply LED Errors 194 POST Error Codes 195 Processor Board LEDs 202 SCSI LEDs 203 SCSI Error Codes 203 SMBUS Error (3-3-2 204 Undetermined Problems 205 System Management Codes 208
4 Netfinity Server...
Hardware Maintenance Manual - Page 17
...the cause of the options installed in the server. Power-On Self Test (POST): When you can be caused by hardware, software, or a user error. When this occurs, work ...available to help identify and resolve hardware-related problems:
Diagnostic programs Power-on self-test (POST) POST beep codes Error messages Troubleshooting charts System error log Option diskettes
Diagnostic Programs: The server ...
Hardware Maintenance Manual - Page 21
... page 205. 4. You might need a scratch diskette to "Undetermined Problems" on already, shut down your IBM reseller or IBM marketing representative. 5. If the server is set , the server prompts you must enter the administrator password to obtain accurate test results for Diagnostics appears, press F2. Netfinity 7000-M10 -
Turn on the third reset; Type in the...
Hardware Maintenance Manual - Page 37
... you can enter either password to a limited set , POST does not complete until you enter the password.
Netfinity 7000-M10 - This limited access might include changing or deleting the power-on the full Configuration/Setup Utility main menu. When a power-on password is set, you type them.)
Type of choices on password
Results
No password required to complete the...
Hardware Maintenance Manual - Page 43
...on page 36. See the instructions that are required for installation and configuration. Resolve configuration conflicts. Type 8680 35 Install the adapter in the server. See "Resolving Configuration Conflicts" on page 146.
3. See "The Configuration/Setup Utility Program" on the device. Set jumpers or switches on page 25.
2. Netfinity 7000-M10 - Set jumpers or switches on page...
Hardware Maintenance Manual - Page 53
... Novell NetWare operating system
IBMSPN.NLM
Notes
1. Type 8680 45 Netfinity 7000-M10 - You will need to perform any additional steps to finish installing your device drivers. Required Device Drivers: The following instructions to complete the device driver installation.
1. IBM Netfinity 7000-M10 Device Drivers for Advanced System Management, version 1.00 or Advanced System Management Device...
Hardware Maintenance Manual - Page 62
Other Configuration Settings Functions: The
Configurations Settings window also includes three additional buttons:
Button Refresh
Reset
Description
Select Refresh to update all data that is checked, the system management subsystem will wait for the system's operating system shutdown to complete before powering off delay field shows
...
Hardware Maintenance Manual - Page 73
...error messages. Print to File
Saves the contents of the System Management Subsystem Logs window. If you are using the Advanced System Management service with an Netfinity Advanced System Management PCI Adapter installed...components monitored by IBM servicers in the System Management Subsystem Log window).
Clear Log
Erases all entries that begin with a Netfinity 7000 server, the event...
Hardware Maintenance Manual - Page 146
Some of the steps are required only during the initial installation of the server support hot-swap drives only. Installing a Drive in a Hot-Swap Bay." Automatically Assigned SCSI ...to install the drive. 2. The default SCSI ID for instructions about setting device jumpers or switches that come with the SCSI device for each SCSI controller is terminated. Check the instructions that...
Hardware Maintenance Manual - Page 189
... server, be sure that the network-adapter device driver supports multiple processors. b. Refer to server components or the adapter. otherwise, go to install or remove, do so
now;
Rotate the adapter retention latch until it with the installation or operation of network adapters. Type 8680 181 Set any cables to your network-adapter documentation for...
Hardware Maintenance Manual - Page 190
... problems can cause false errors and symptoms. 2. The Symptom-to -FRU Index
This index supports Netfinity 7000-M10 -
Check the configuration before you decide which FRUs to help you replace a
FRU. I /O Board
1. Processor Board
1. I /O Function Card 2. I /O Board 3. Use this Symptom-to-FRU Index to have available when servicing the computer. For IBM devices not supported...
Hardware Maintenance Manual - Page 203
... power supply switch is still off, replace the following components in the following error codes, X can be flashing; if not, replace the power control card.
3. Connect the power cord; All remeinting componets, one at a time. Power Supply
On
On
Description:
Power is on, remove the jumper you installed on the power control card should be...
Hardware Maintenance Manual - Page 220
... system error log and follow the instruction for the following problems listed. Replace the FRU for the error in the log. 2. Memory Board c. 212 Netfinity Server HMM
Table 15 (Page 4 of 4). System Management Codes
Code/Description
FRU/Action
C0 (SMI error)
1. Processor Board
Memory related error: a. Processor b. PCI related error: a. DIMM b. Adapter b. See system error log...
Hardware Maintenance Manual - Page 244
... cables can be disconnected whenever the fan assembly is not installed in the installation and configuration procedures. There are present inside the power supplies, power backplane, or AC box.
Caution: Never remove the cover on top of the rack model of these parts, contact an IBM service technician. Caution: The power cable to the fan should...
IBM 86807RY Reviews
Do you have an experience with the IBM 86807RY that you would like to share?
Earn 750 points for your review!
We have not received any reviews for IBM yet.
Earn 750 points for your review!