Manual
Page 17
...OS does not support USB controller, please contact OS vendor for possible patch or driver upgrade. Center/Subwoofer Speaker Out The default Center/Subwoofer Speaker Out jack. USB port Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner.../Subwoofer Speaker Out jack. COM A (Serial Port) Connects to the lower port (purple). Also make sure your OS supports USB controller. Parallel Port The parallel port allows connection of 10/100/1000Mbps. LAN Port The provided Internet connection is Gigabit Ethernet, ...
...OS does not support USB controller, please contact OS vendor for possible patch or driver upgrade. Center/Subwoofer Speaker Out The default Center/Subwoofer Speaker Out jack. USB port Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner.../Subwoofer Speaker Out jack. COM A (Serial Port) Connects to the lower port (purple). Also make sure your OS supports USB controller. Parallel Port The parallel port allows connection of 10/100/1000Mbps. LAN Port The provided Internet connection is Gigabit Ethernet, ...
Manual
Page 23
To connect an AC97 front panel audio module to this connector. Check the pin assignment carefully while you connect the front USB cable, incorrect connection between the module and connector will make the audio device unable to work or even damage it . ... NC 5 LINE2_R 5 Line Out (R) 6 FSENSE1 6 NC 7 FAUDIO_JD 7 NC 8 No Pin 8 No Pin 9 LINE2_L 9 Line Out (L) 10 FSENSE2 10 NC By default, the audio driver is configured to this connector, please refer to work or even damage it . Pin No. Definition Pin No. If you connect the front panel audio...
To connect an AC97 front panel audio module to this connector. Check the pin assignment carefully while you connect the front USB cable, incorrect connection between the module and connector will make the audio device unable to work or even damage it . ... NC 5 LINE2_R 5 Line Out (R) 6 FSENSE1 6 NC 7 FAUDIO_JD 7 NC 8 No Pin 8 No Pin 9 LINE2_L 9 Line Out (L) 10 FSENSE2 10 NC By default, the audio driver is configured to this connector, please refer to work or even damage it . Pin No. Definition Pin No. If you connect the front panel audio...
Manual
Page 55
...installed with the GPL regulations. 4. Xpress Recovery2 will store the backup file at the end of Xpress Recovery2, a primary partition must be backed up) 4. USB hard disks are currently not supported. 6. PATA IDE primary channel b. SATA IDE channel 3 f. When using hard disks with more than data restoration. 3. ...a. REMOVE: Remove previously-created backup files to Xpress Recovery. 2. On a few motherboards based on the size of backing up data from the driver CD before data backup. 2. SATA IDE channel 2 e. Limitations: 1. PATA IDE secondary channel c .
...installed with the GPL regulations. 4. Xpress Recovery2 will store the backup file at the end of Xpress Recovery2, a primary partition must be backed up) 4. USB hard disks are currently not supported. 6. PATA IDE primary channel b. SATA IDE channel 3 f. When using hard disks with more than data restoration. 3. ...a. REMOVE: Remove previously-created backup files to Xpress Recovery. 2. On a few motherboards based on the size of backing up data from the driver CD before data backup. 2. SATA IDE channel 2 e. Limitations: 1. PATA IDE secondary channel c .
Manual
Page 76
...2 (or previous versions) to a RAID array. Solutions 1: Use the NVRAID tool (nForce Driver Version 5.xx) to convert the boot volume to a bootable RAID volume. Here are two ...21/22). CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Integrated Peripherals IDE Configuration USB Configuration SATA-II Configuration Onboard Audio Function Onboard LAN Function Onboard LAN Boot ROM Onboard...: Save F6: Fail-Safe Defaults Figure 22 ESC: Exit F1: General Help F7: Optimized Defaults GA-M51GM-S2G Motherboard - 76 - Save settings and exit the BIOS setup. There are the detailed step-by-step...
...2 (or previous versions) to a RAID array. Solutions 1: Use the NVRAID tool (nForce Driver Version 5.xx) to convert the boot volume to a bootable RAID volume. Here are two ...21/22). CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Integrated Peripherals IDE Configuration USB Configuration SATA-II Configuration Onboard Audio Function Onboard LAN Function Onboard LAN Boot ROM Onboard...: Save F6: Fail-Safe Defaults Figure 22 ESC: Exit F1: General Help F7: Optimized Defaults GA-M51GM-S2G Motherboard - 76 - Save settings and exit the BIOS setup. There are the detailed step-by-step...
Manual
Page 14
... [Enabled] [Auto] Item Help Menu Level} IDE2 Conductor Cable [Auto] Serial-ATA-II 1 [Enabled] Serial-ATA-II 2 [Enabled] On-Chip USB USB Keyboard Support USB Mouse Support [V1.1+V2.0] [Disabled] [Disabled] Onboard Audio Function [Auto] Onboard LAN Function [Auto] Onboard LAN Boot ROM [Disabled] Onboard 1394 Function... Windows 2000 with Service Pack 2 (or previous versions) to a RAID array. Solutions 1: Use the NVRAID tool (nForce Driver Version 5.xx) to convert the boot volume to a bootable RAID volume. Step 2: After system restarts, press Del to resolve this issue.
... [Enabled] [Auto] Item Help Menu Level} IDE2 Conductor Cable [Auto] Serial-ATA-II 1 [Enabled] Serial-ATA-II 2 [Enabled] On-Chip USB USB Keyboard Support USB Mouse Support [V1.1+V2.0] [Disabled] [Disabled] Onboard Audio Function [Auto] Onboard LAN Function [Auto] Onboard LAN Boot ROM [Disabled] Onboard 1394 Function... Windows 2000 with Service Pack 2 (or previous versions) to a RAID array. Solutions 1: Use the NVRAID tool (nForce Driver Version 5.xx) to convert the boot volume to a bootable RAID volume. Step 2: After system restarts, press Del to resolve this issue.