Manual
Page 15
..., the installation is to install.) Step 3: Place the cooler atop the CPU, aligning the four push pins through the pin holes on the motherboard. Use extreme care when removing the CPU cooler because the thermal grease/tape between the CPU cooler and CPU may damage the CPU. - 15 - Hardware Installation Check...
..., the installation is to install.) Step 3: Place the cooler atop the CPU, aligning the four push pins through the pin holes on the motherboard. Use extreme care when removing the CPU cooler because the thermal grease/tape between the CPU cooler and CPU may damage the CPU. - 15 - Hardware Installation Check...
Manual
Page 28
...to the power connector in the correct orientation. Do not insert the power supply cable s into pins under the protective covers when using an Intel Extreme Edition CPU (130W). • To meet expansion requirements, it is recommended that a power supply that does not provide the required power, the ... 3.3V -12V GND PS_ON(soft On/Off) GND GND GND -5V +5V +5V +5V (Only for 2x12 pinATX) GND (Only for 2x12 pinATX) GA-EX58-UD5P/UD5 Motherboard - 28 - When using a power supply providing a 2x4 12V and a 2x12 power connector, remove the protective covers from the 12V power connector and ...
...to the power connector in the correct orientation. Do not insert the power supply cable s into pins under the protective covers when using an Intel Extreme Edition CPU (130W). • To meet expansion requirements, it is recommended that a power supply that does not provide the required power, the ... 3.3V -12V GND PS_ON(soft On/Off) GND GND GND -5V +5V +5V +5V (Only for 2x12 pinATX) GND (Only for 2x12 pinATX) GA-EX58-UD5P/UD5 Motherboard - 28 - When using a power supply providing a 2x4 12V and a 2x12 power connector, remove the protective covers from the 12V power connector and ...
Manual
Page 45
... CPU Features QPI Link Speed QPI Link Speed UnCore & QPI Features Base Clock(BCLK) Control x BCLK Frequency (Mhz) Advanced Clock Control Performance Enhance Extreme Memory Profile (X.M.P.) (Note 2) System Memory Multiplier (SPD) Memory Frequency (Mhz) 1066 DRAM Timing Selectable Profile DDR Voltage Profile QPI Voltage >>>>> Channel A x CAS Latency Time x tRCD...
... CPU Features QPI Link Speed QPI Link Speed UnCore & QPI Features Base Clock(BCLK) Control x BCLK Frequency (Mhz) Advanced Clock Control Performance Enhance Extreme Memory Profile (X.M.P.) (Note 2) System Memory Multiplier (SPD) Memory Frequency (Mhz) 1066 DRAM Timing Selectable Profile DDR Voltage Profile QPI Voltage >>>>> Channel A x CAS Latency Time x tRCD...
Manual
Page 49
...Allows you to adjust the amplitude of the CPU and North Bridge clock. Options are : 700mV, 800mV, 900mV (default), 1000mV. Extreme Memory Profile (X.M.P.) (Note) Allows the BIOS to read the SPD data on XMP memory module(s) to operate at its best performance...are : 0ps~750ps. (Default: 0ps) ******* Advanced DRAM Features******* CMOS Setup Utility-Copyright (C) 1984-2008 Award Software Advanced DRAM Features Performance Enhance Extreme Memory Profile (X.M.P.) (Note) System Memory Multiplier (SPD) Memory Frequency (Mhz) 1066 [Turbo] [Disabled] [Auto] 1066 Item Help Menu Level...
...Allows you to adjust the amplitude of the CPU and North Bridge clock. Options are : 700mV, 800mV, 900mV (default), 1000mV. Extreme Memory Profile (X.M.P.) (Note) Allows the BIOS to read the SPD data on XMP memory module(s) to operate at its best performance...are : 0ps~750ps. (Default: 0ps) ******* Advanced DRAM Features******* CMOS Setup Utility-Copyright (C) 1984-2008 Award Software Advanced DRAM Features Performance Enhance Extreme Memory Profile (X.M.P.) (Note) System Memory Multiplier (SPD) Memory Frequency (Mhz) 1066 [Turbo] [Disabled] [Auto] 1066 Item Help Menu Level...
Manual
Page 50
Options are : Auto (default), 1~63. Profile DDR Voltage When using a non-XMP memory module or Extreme Memory Profile (X.M.P.) is set to Profile1, this item will display the value based on the SPD data on the CPU being used ....16. When Extreme Memory Profile (X.M.P.) is set the system memory multiplier. tRAS Options are : Auto (default), Manual. Profile QPI Voltage The value displayed here is automatically adjusted according to the BCLK Frequency (Mhz) and System Memory Multiplier settings. ESC: Exit F1: General Help F7: Optimized Defaults GA-EX58-UD5P/UD5 Motherboard - ...
Options are : Auto (default), 1~63. Profile DDR Voltage When using a non-XMP memory module or Extreme Memory Profile (X.M.P.) is set to Profile1, this item will display the value based on the SPD data on the CPU being used ....16. When Extreme Memory Profile (X.M.P.) is set the system memory multiplier. tRAS Options are : Auto (default), Manual. Profile QPI Voltage The value displayed here is automatically adjusted according to the BCLK Frequency (Mhz) and System Memory Multiplier settings. ESC: Exit F1: General Help F7: Optimized Defaults GA-EX58-UD5P/UD5 Motherboard - ...
Manual
Page 86
...Close (Application will enter Stealth Mode) 14 Minimize (Application will automatically reset when the total power saving reaches 99999999 Watts. GA-EX58-UD5P/UD5 Motherboard - 86 - Re-enter the application only if you want to make any changes or completely close the application. ...time . (Note 4) Total Mode - system performance may be affected. (Note 3) 1: Normal Power Saving (default); 2: Advanced Power Saving; 3: Extreme Power Saving. (Note 4) The total amount of time since activating Dynamic Energy Saver Advanced for the latest utility version) C. Stealth Mode In Stealth...
...Close (Application will enter Stealth Mode) 14 Minimize (Application will automatically reset when the total power saving reaches 99999999 Watts. GA-EX58-UD5P/UD5 Motherboard - 86 - Re-enter the application only if you want to make any changes or completely close the application. ...time . (Note 4) Total Mode - system performance may be affected. (Note 3) 1: Normal Power Saving (default); 2: Advanced Power Saving; 3: Extreme Power Saving. (Note 4) The total amount of time since activating Dynamic Energy Saver Advanced for the latest utility version) C. Stealth Mode In Stealth...