Garmin Reactor 40 Steer-by-wire Standard Corepack Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin Reactor 40 Steer-by-wire Standard Corepack manuals!
Problems with Garmin Reactor 40 Steer-by-wire Standard Corepack?
Ask a Question
Free Garmin Reactor 40 Steer-by-wire Standard Corepack manuals!
Problems with Garmin Reactor 40 Steer-by-wire Standard Corepack?
Ask a Question
Popular Garmin Reactor 40 Steer-by-wire Standard Corepack Manual Pages
Installation Instructions PDF - Page 1
... and is 3 m (9 ft.) long.
◦ If the CCU cannot be cut. REACTOR™ 40 STEER-BYWIRE
Installation Instructions
Important Safety Information
WARNING See the Important Safety and Product Information guide in the water, such as you use a handheld compass to promptly regain manual control of screws.
If the provided screws are available from the center of your boat...
Installation Instructions PDF - Page 2
...) wire.
Mount the CCU away from the autopilot system, and you can be built using the included TconnectorsNMEA 2000® Connection Considerations, page 2.
After you are included in the helm control box. Detailed mounting instructions are connecting the autopilot to optional NMEA® 0183 devices, such as indicated in the product specifications. NMEA...
Installation Instructions PDF - Page 3
...steering controller CAN bus is not long enough, extend the appropriate wires with 0.08 mm2 (28 AWG) wire. Additional instructions are supplied with the steering controller. Alarm Wire Color White (+) Black (-)
CCU Cable Wire Color Orange (+) Blue (-)
3 Solder and cover all the parts... same ground as a compatible Garmin chartplotter to install the alarm (Installing the Alarm, page 3). NOTE...
Installation Instructions PDF - Page 4
... RX port.
These wiring diagrams are configured on the wiring harness. • See Specifications, page 5 for the helm control (optional) or a compatible Garmin chartplotter. The corresponding A and B wires of each internal port should be configured and tuned to your chartplotter for the CCU to the NMEA 2000 backbone by following the instructions provided with your boat...
Installation Instructions PDF - Page 5
...;
Helm control
Â
NMEA 0183 compatible device
Ã
Wire Helm Control Wire Color -
Specifications
CCU
Specification
Measurement
Dimensions (L × W × H)
170 ...Wire If your NMEA 0183 compatible device has only one transmitting wire (Tx), it to the blue wire (Tx/A) from the helm control, and leave the white wire (Tx/B) from the helm control must be connected to www.garmin...
Installation Instructions PDF - Page 6
... support.garmin.com for 5 seconds
• Autopilot transitions to optional NMEA 0183 compatible devices, the autopilot uses the following NMEA 0183 sentences. Reactor™ is a trademark of turn 127250 Vessel heading 127258 Magnetic variation 127488 Engine parameters: Rapid update 128259 Water speed 129025 Position: Rapid update 129026 COG & SOG: Rapid update 129283 Cross track error 129284...
Configuration Guide PDF - Page 1
...
REACTOR™ 40 STEER-BYWIRE
Configuration Guide
Important Safety Information
WARNING See the Important Safety and Product Information guide ...Setup > Dealer
Autopilot Setup > Wizards > Dockside Wizard. • On a chartplotter, select Settings > My Vessel >
Autopilot Installation Setup > Wizards > Dockside Wizard. 3 Select the vessel type. 4 Test the steering direction (Testing the Steering...
Configuration Guide PDF - Page 2
... instead of performing zigzag motions, select Reverse Steering Dir. > Run Normal Autotune on a helm control or Switch Direction > Run Standard Autotune on a chartplotter select OK. • If the calibration is shown.
You can review the gain values provided on a chartplotter, select Settings > My Vessel > Autopilot Installation Setup > Compass Setup > Compass Cal. > Begin.
2 Follow the...
Configuration Guide PDF - Page 3
... the heading screen, select Menu > Setup > Dealer Autopilot Setup > Autopilot Tuning > Acceleration Limiter.
• On a chartplotter, select Settings > My Vessel > Autopilot Installation Setup > Autopilot Tuning > Accel.
Setting North Before you are performing this procedure, you should record the values set by a trusted heading indicator, such as part of the Sea Trial Wizard, proceed...
Configuration Guide PDF - Page 4
... in order to allow a higher turn overshoot. On a chartplotter, select Settings > My Vessel > Autopilot Installation Setup > Autopilot Tuning. You can calibrate the compass, run the autotune procedure, and set this manual (Detailed Configuration Settings, page 4). 5 Configure the value of autopilot- Advanced Configuration Settings
You can increase the percentage to limit the turn rate...
Configuration Guide PDF - Page 5
... value.
NMEA 2000, Tachometer, or GPS. High Speed Counter: Allows you can adjust the value. On a chartplotter, selectSettings > My Vessel > Autopilot Installation Setup > Steering System Setup.
5 Speed Source Settings On a helm control, select Menu > Setup > Dealer Autopilot Setup > Speed Source Setup. If the value does not match the value on the helm control or chartplotter, you to Lock...
Garmin Reactor 40 Steer-by-wire Standard Corepack Reviews
We have not received any reviews for Garmin yet.