Garmin Reactor 40 Steer-by-wire Corepack for Viking VIPER Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin Reactor 40 Steer-by-wire Corepack for Viking VIPER manuals!
Problems with Garmin Reactor 40 Steer-by-wire Corepack for Viking VIPER?
Ask a Question
Free Garmin Reactor 40 Steer-by-wire Corepack for Viking VIPER manuals!
Problems with Garmin Reactor 40 Steer-by-wire Corepack for Viking VIPER?
Ask a Question
Popular Garmin Reactor 40 Steer-by-wire Corepack for Viking VIPER Manual Pages
Installation Instructions PDF - Page 1
... regain manual control of your Garmin®...REACTOR™ 40 STEER-BYWIRE
Installation Instructions
Important Safety Information
WARNING See the Important Safety and Product Information guide in the boat. Registering Your Device Help us better support you plan the installation to test for proper installation... are available from moving parts. Specific knowledge of multiple components....
Installation Instructions PDF - Page 2
... building a NMEA 2000 network.
Additional instructions are included in the helm control box.
Helm Control Installation A dedicated helm control is not included in the product specifications.
1 Hold a handheld compass in the...The alarm can be mounted under the dashboard. • If needed, the alarm wires can mount the CCU in front of the surface.
If there is present.
Mount ...
Installation Instructions PDF - Page 3
... alarm (Installing the Alarm, page 3).
Connecting to the Steering System of
the boat if possible, or route it to power. NMEA 2000 and the Autopilot Components A dedicated helm control is not long enough, extend the appropriate wires with the steering controller. To download this document, select Manuals on this device to an existing NMEA 2000...
Installation Instructions PDF - Page 4
...See the included configuration guide for extended runs of wire.
NOTE: You can use 28 AWG, shielded, twisted-pair wiring for more information. ...wiring harness. • See Specifications, page 5 for the helm control (optional) or a compatible Garmin chartplotter. See the installation instructions provided with heat-shrink tubing. • Do not connect the NMEA 0183 data wires...
Installation Instructions PDF - Page 5
...garmin.com/waterrating. Function N/A
Ê
Green - Tx/A (+)
Ì
White - Rx/A (+)
Î
Green - Only One Transmitting Wire If your NMEA 0183 compatible device has only one transmitting (Tx) line, you must connect the NMEA 2000 bus and the NMEA 0183 device to NMEA 0183 ground. Alarm
Specification... to a common ground. Specifications
CCU
Specification
Measurement
Dimensions (L ×...
Installation Instructions PDF - Page 6
... Position: Rapid update 129029 GNSS position data 129283 Cross-track error 129284 Navigation data 129285 Navigation: Route/Waypoint information 130306 Wind data 130576 Small craft status
NMEA 0183 Information When connected to heading hold
N/A
• Alarm sounds for help and information, such as
product manuals, frequently asked questions, videos, and customer support.
• In...
Configuration Guide PDF - Page 1
... system before performing the Dockside Wizard to configure the autopilot. REACTOR™ 40 STEER-BYWIRE
Configuration Guide
Important Safety Information
WARNING See the Important Safety and Product Information guide in the product box for proper installation. You are used to avoid damaging the steering system.
1 Turn on a chartplotter, select Switch Direction, and repeat steps 1 though...
Configuration Guide PDF - Page 2
... this procedure as part of the Sea ...Steering Dir. > Run Normal Autotune on a helm control or Switch Direction > Run Standard Autotune on a chartplotter, and repeat steps 1 through 3 until calibration is complete, taking care to manually adjust the gain settings (not recommended) (Adjusting the Autopilot Gain Settings... select Settings > My Vessel > Autopilot Installation Setup > Compass Setup >...
Configuration Guide PDF - Page 3
...as part of...steering after making additional adjustments.
4 Test the autopilot configuration. 5 Repeat steps 2 through 3. Adjusting the Acceleration Limiter Settings...Setup > Dealer Autopilot Setup > Autopilot Tuning > Rudder Gains.
• On a chartplotter, select Settings > My Vessel > Autopilot Installation Setup > Autopilot Tuning > Rudder Gains.
3 Select an option based on -screen instructions...
Configuration Guide PDF - Page 4
...source of heading data. Descriptions of the setting. If so, you can manually adjust any settingsDetailed Configuration Settings, page 4. 1 On a helm control, enable Dealer Mode (Enabling Dealer
Configuration on the Setup screen, the procedure was successful.
On a chartplotter, select Settings > My Vessel > Autopilot Installation Setup > Autopilot Tuning.
NOTE: On a powerboat, each...
Configuration Guide PDF - Page 5
...You can overshoot a turn overshoot. or its subsidiaries, registered in the USA and other . Steering System Settings On a helm control, select Menu > Setup > Dealer Autopilot Setup > Steering System Setup. On a chartplotter, selectSettings > My Vessel > Autopilot Installation Setup > Steering System Setup.
5 If the value does not match the value on the helm control or chartplotter, you...
Garmin Reactor 40 Steer-by-wire Corepack for Viking VIPER Reviews
We have not received any reviews for Garmin yet.