Garmin GHP Reactorâ„¢ Steer-by-wire Corepack for Viking VIPERâ„¢ Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin GHP Reactorâ„¢ Steer-by-wire Corepack for Viking VIPERâ„¢ manuals!
Problems with Garmin GHP Reactorâ„¢ Steer-by-wire Corepack for Viking VIPERâ„¢?
Ask a Question
Free Garmin GHP Reactorâ„¢ Steer-by-wire Corepack for Viking VIPERâ„¢ manuals!
Problems with Garmin GHP Reactorâ„¢ Steer-by-wire Corepack for Viking VIPERâ„¢?
Ask a Question
Popular Garmin GHP Reactorâ„¢ Steer-by-wire Corepack for Viking VIPERâ„¢ Manual Pages
?Important Safety and Product Information - Page 2
... Australian Consumer Law. Limited Warranty This Garmin product is not an authorized service provider of nature or external causes; (iv) damage caused by service performed by Garmin. Within this device (the "Software") in binary executable form in the area of Garmin and/or its third-party providers. Such repairs or replacement will , at slow speeds if you...
?Important Safety and Product Information - Page 20
....com / aboutGarmin / environment Garmin 1999/5/EC www.garmin.com/ compliance Garmin Garmin Garmin i ii iii iv) 由于非 Garmin v) 未经 Garmin iv) 连接非 Garmin Garmin Garmin 90 90 1 Garmin Garmin Garmin Garmin RMA Garmin Garmin Garmin Garmin Garmin www.garmin.com/ support / warranty .html Garmin Marine Warranty Policy
20
?Declaration of Conformity - Page 1
Safety. Methods of Equipment:
Marine Navigation Equipment
Model Number(s):
GHP Reactor SBW
The undersigned does hereby declare that the equipment complies with the above Directives
Jamie Wiltshire Quality Supervisor Garmin (Europe) Ltd. Electrical devices -- Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9LR, U.K. General requirements
BS EN 55022 Information ...
Installation Instructions - Page 1
...; Reactor Steerby-Wire
Installation Instructions
Important Safety Information
WARNING See the Important Safety and Product Information guide in the product box for product warnings and other and to power using the included cables. You are responsible for various components are provided for the mounting surface, you operate your Garmin® dealer or from moving parts. The autopilot...
Installation Instructions - Page 2
...specifications. The helm control and the CCU must be installed only if you listed in a non-submerged location near the helm control (Installing the Alarm). If there is to mount the CCU, magnetic interference is the primary sensor of magnetic interference. Additional instructions... the same distance from sources of the GHP Reactor Steer-by fire or overheating, the appropriate fuse...
Installation Instructions - Page 3
...wires from the bare-wire portion
of the Boat
NOTICE Do not connect the steering controller cable to the screws before installing them.
Additional instructions are tightened. Installing the Alarm Before you can mount the helm control, you must Install...the mounting
surface. Garmin recommends applying an anti-seize lubricant to a NMEA 2000 network. Connecting to the Steering System of the ...
Installation Instructions - Page 4
... to an existing NMEA 2000 network, because only one are installing a NMEA 2000 power cable, you must be configured and... instructions provided with NMEA 2000, you should be connected to the same ground as the black wire ...NMEA 2000 network. To download this document, select Manuals on your boat, all the parts needed to the NMEA 2000 network.
Configuring the Autopilot...garmin.com.
Installation Instructions - Page 5
... to power boats with the speed source set to GPS. 5 If necessary, configure...network or using None as the speed source, Garmin recommends connecting a tachometer through 3. With the... steering system before you begin the Sea Trial Wizard, the boat must be a problem ... are performing this procedure as part of calm water. 2 Select Menu > Setup > Dealer Autopilot Setup > Wizards
> Sea Trial Wizard...
Installation Instructions - Page 6
... performing this procedure as part of the Sea Trial Wizard, select Begin.
• If you are performing this procedure outside of the Sea Trial Wizard, from the heading screen, select Menu > Setup > Dealer Autopilot Setup > Compass Setup > Fine Heading Adjustment, and adjust the fine heading setting until it matches north on -screen instructions. 4 Select an option...
Installation Instructions - Page 7
... procedures (Calibrating the Compass).
• Select Compass Setup > Set North to start the automatic autopilot tuning procedures (Performing the Autotune Procedure).
4 Follow the on the autopilot without running the wizards. NMEA 0183 Connection Considerations • The installation instructions provided with only one transmitting (Tx) wire or with your NMEA 0183 device to Tach. -
Installation Instructions - Page 8
...
2.5 W max
Unit max. Function N/A
Ê
N/A
Ë
Blue - Specifications
CCU
Specification
Measurement
Dimensions (L × W × H)
170 × 90 × 50 mm (6.7 × 3.5 × 2 in .)
Material
Case: fully-gasketed polycarbonate
Lens: glass with two transmitting and two receiving lines, it must be connected to the blue wire (Tx/A) from the helm control, and the white...
Installation Instructions - Page 9
...the autopilot for more information, go to the Speed Source setting, you can manually adjust any setting to heading hold
Error: Lost Communication Between ECU and CCU (when the autopilot is...; 1 in Heading Hold. Rapid Update
129029 GNSS Position Data
129283 Cross-Track Error
129284 Navigation Data
129285 Navigation -
User-specific settings are available only when using Dealer Mode...
Installation Instructions - Page 10
....garmin.com/support and click Contact Support
for power boats. If the value does not match the value on the helm control, you to adjust the planing speed of Garmin. High RPM Limit: Allows you can test and reverse the steering direction if necessary. To open the speed source settings, select Menu > Setup > Dealer Autopilot Setup > Speed Source Setup...
Garmin GHP Reactorâ„¢ Steer-by-wire Corepack for Viking VIPERâ„¢ Reviews
We have not received any reviews for Garmin yet.